Sziasztok!
A tévé nem ad hangot. Egyik bemenetről sem. Letöltöttem a szervizkönyvet, és
" Service Modes, Error Codes, and Fault FindingEN 12 TCM2.0E LA5.
5. Service Modes, Error Codes, and Fault Finding
Index of this chapter:
5.1 Test Points
5.2 Service Modes
5.3 Error Codes
5.5 Service Tools
5.1 Test Points
This chassis is NOT equipped with test points in the service
printing. No test points are mentioned in the service manual.
5.2 Service Modes
The Service Mode feature is split into different parts:
• Service Alignment Mode (SAM).
• Service Default Mode (SDM).
• Customer Service Mode (CSM).
SDM and SAM offer features, which can be used by the Service
engineer to repair/align a TV set. Some features are:
• Activates the blinking LED procedure for error identification
when no picture is available (SDM).
• Make alignments (e.g. white tone), (de)select options,
enter options codes, reset the error buffer (SAM).
• Display information (“SAM” indication in upper right corner
of screen, error buffer, software version, options and option
codes, sub menus).
The CSM is a Service Mode that can be enabled by the
consumer. The CSM displays diagnosis information, which the
customer can forward to the dealer or call centre. In CSM
mode, “CSM”, is displayed in the top right corner of the screen.
The information provided in CSM and the purpose of CSM is to:
• Increase the home repair hit rate.
• Decrease the number of nuisance calls.
• Solved customers' problem without home visit.
5.2.1 Service Alignment Mode (SAM)
How to Enter
To enter SAM, use the following method:
• Press on the remote control the code “062596” directly
followed by the “INFO” key.
After entering SAM, the following screen is visible, the values
can be adjusted according to the requested (see Chapter 8"
Szóval a saját távirányítóján az INFO gomb helyén időzítő óra jele látható. Ha beütöm a 062596 kódot, az első két szám után jön az üzenet, hogy nincs ilyen csatorna, de ha nem hagyom abba, és végig nyomom a 6 számjegyet, majd az INFO gombnak megfelelőt. (Megkerestem a képét a NET-en) akkor sem lép be.
Van valakinek ötlete, vagy más kódja?
Előre is köszönöm!
T.
üdv: tudom, nehéz dió.
Keresem ennek a távnak a rajzát.
Hiányzik róla két ellenállás (3003 és 3005) és a ledek meghajtó tranzisztorai.
Bálint
Szevasztok
Hozták ezt a fentebb leirt tv t,csatorna keresésnél,nem ál meg a megtalált csatornán hanem tovább megy.
Az5100 ás AFC tekercsben a kondit helyettesitettem külsővel ,de semmi változás.Valami segitség kellene a hiba feltárásához.
Sziasztok
Szívok ezzel a tv-vel. AS15 csere volt, ami egyértelmű. Utána néha kikapcsolt, el se indult stb. A tápot átforrasztottam, s minden ok lett. (bár most utólag inkább gyanúzok a kontakt hibás táp és main összekötő kábelre..
A TV nálam szuperül megy. Elvitték. Majd visszajön, hogy fél óra után zúg a tv, s hdmi-ről zöld a kép. Kipróbálom, nálam megy hibátlanul, s mind a 4 hdmi OK.. Elmondom.. Háát. Nem fél óra, 5-6 óra után volt hangja, s a hdmi fél óra után volt zöld. OK.. Bevittem a gyerek szobájába, ott van HDMI-s media player. 2 órán át ment, természetesen full hibátlanul..
VISZONT.. A tv hátulja k. meleg volt. a VGA csati a mainboardon szinte forró volt.. Szétkaptam, a mainon megmértem az elkókat, elvileg OK.. De nem egyértelmű, mert a tápban kerámia kondik végzik a piszkos munkát a nagyfrekis táp miatt.. Összedobva elsőre megint nem indult, a kábel átmozgatásával ok, ezért gondolom, lehet a kábel kontaktos.. NA mindegy..
5 perc, s már forró a proc a lapon.. Nem a hűtőbordás FHD 100Hz-es PNX5100, hanem a hűtőborda nélküli PNX8543, pedig még csak nem is dolgozott sokat, nem volt semmi rádugva, csak a fekete kép volt, meg a menürendszer.. EZ normális? 5 perc alatt szinte forró lett.. A TV nálam megy órákat, de ha mondjuk nem ekkora nyílt helyen van, hanem pl egy polc alatt félig a szekrényben, hihető, hogy felforr.. Valakinek van ezzel tapasztalata? Van otthon egy másik ugyan ilyen mainom, tesztre, az is forró lett.. De lehet az is hibás.. Csak ez így már gyanús..
L