Service manuals, schematics, eproms for electrical technicians

PHILIPS HQ4601A ECLIPSE RECHARGEABLE SHAVER

HOUSEHOLD - SERVICE MANUAL
Type: (PDF)
Size
144.6 KB
Page
2
Category
HOUSEHOLD
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar philips manual?
Advertisements
Document preview [1st page]
PHILIPS HQ4601A ECLIPSE RECHARGEABLE SHAVER service manual (1st page)
Preview of PHILIPS HQ4601A ECLIPSE RECHARGEABLE SHAVER [1st page]
Click on the link for free download!
Document preview [2nd page]
PHILIPS HQ4601A ECLIPSE RECHARGEABLE SHAVER service manual (2nd page)
Preview of PHILIPS HQ4601A ECLIPSE RECHARGEABLE SHAVER [2nd page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
  • Also known:
    PHILIPS HQ-4601A ECLIPSE SHAVER HQ4601A HQ 4601
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant HOUSEHOLD forum topics:
PHILIPS HR6835 porszívó motorja nem megy, tud-e valaki tanácsot adni a javításhoz? Megoldódott, 10 cm tápkábelt levágtam
Tisztelt Kollégák, a fenti porszívó nem megy (a vízszivattyú lámpa sem világít). Mivel 10 perc alatt nem találtam meg a szétszedés mikéntjét (a google sem segített), inkább a rutinosabb kollégákhoz fordulok segítségért. Közben itt találtam 6841 SM-et, most azt nézem. köszönettel bbgames
Philips-Whirlpool ADG-622 mosogatógép
Sziasztok! A címben szereplő mosogatógép az anyós-jelöltem konyhájában lustálkodik. Nekem ugyan nincs túl nagy tapasztalatom a háztartási gépek javításában (bár a saját mosogatógépünk már megjavítottam egyszer) de szerelőre fordítható pénz híján kénytelenek velem is beérni. A probléma látszólag egyszerű: mosás után foltosak maradnak az elmosott eszközök (maga a gép is). Só van benne, közepesről maximálisra átállítva az adagolást sem változott a helyzet. Ötlete valakinek?
Philips porszivó csapágy csere. Hogyan?
Helo.Szétment e porszivó csapágya.Nem tudom kibontani a turbinás részt .Kérlek beneteket segitsetek.Köszönettel Deák Ferencz.
Philips HP5847 shaver stopped working
Hope I've selected the right forum, I don't speak Hungarian! I have a Philips shaver HP5847 in which I was replacing the rechargeable battery. Unfortunately while trying to fit it (with long tags attached) something must have shorted out while I was turning the shaver around and it suddenly stopped working (the motor had initially immediately started running as I inserted the pre-charged battery pack). I found the Service Manual on this site but unfortunately there are no component values shown on the schematic. It was helpful to see the circuit diagram and I noted a (small-value) resistor R20 in series with the motor (for load current-sensing). I found no conductivity through it, so I shorted that out and miraculously the motor started working! I checked out the data sheet for the SAA1500T charge controller but other than confirming my understanding of the function of the resistor gave no help in working out what kind of value I should replace it with... I guess it's a function of the actual motor parameters. I imagine it is going to be of the order of 1 Ohm or less but this type of surface mount resistor does not appear to have a value marking on it unlike the other components on the PCB. Can anyone suggest a value for R20 please?
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce