Service manuals, schematics, eproms for electrical technicians
AUDIOAV601.
Type: 
(DJVU)
(DJVU)Size
22.6 KB
22.6 KB
Page
1
1
Category
AUDIO
SERVICE MANUAL
AUDIO
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar audioav manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar audioav manual?
Document preview [1st page]
No preview item for this file.
Possible causes:
- No preview picture generated yet.
- It is not a pdf file.
Advertisements
Please tick the box below to get download link:
- Also known:
AUDIOAV 601
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant AUDIO forum topics:
Sziasztok!
A szóbanforgó rádiós erősítő kikapcsoláskor elfelejti a beállított adókat.
Sehol nem találok ilyen rajzot. Ha lenne valakinek ötlete és/vagy rajza, hálás lennék érte.
Sziasztok! Adott a fentebb megnevezett végfok. Jobb oldala protectbe van. H osztályú,a felépítését a Siva ppa1600-hoz tudnám hasonlítani. (Emeletes táp,stb) A panelon minden emmitter ellenállás, dióda, tranzisztor jónak tűnik. A kimeneten 30v-ot mérek. Úgy néz ki meg is van a baj. Kiszedtem minden végtranyót és az alacsony tápfeszültségű részen zárlatos volt az egyik komplementer pár tranyó. Vélhetően ezeket cserélve ismét működni fog. 5 pár végtranyó van mindkét tápfesz részen és az 5ből 1 pár hajtja meg a másik 4et ha jól látom. A kérdés az, hogy elég cserélnem az alacsony tápfesz részen lévő 5 pár tranyót (természetesen párbaválogatva, vagy a nagyobb feszültségű részen is kellene a stabil működés végett?
Hello everyone,
I've this speaker model:
RCF art 415-A.
The power supply is faulty, no votltage out to the amplifier.
The Mosfets are blown. I've changed the mosfets and it's driver, and still have a problem.
I tried to switch on but only one of the mosfets gets hot (the one which switches the 310. There are 2 of them - Mos5 in the scheme).
Obviously I turned it off.
1) What causes it to heat?
2) Testing the VCC of the LMC555, it's only 2.7V. When taking it out of the circuit, it's 12VDC! What makes the voltage to drop. Where does the supply of the LMC555 come from? The VCC of the 555 should be around 10V, as compared with a good card.
I've changed the 555, but the problem remained. I've checked the components around, resistors and capacitors, and transistors, and seem to be OK.
4) The VCC of the Mosfet driver is 10V, but should be 12V if compared with a good card.
3) Could the trafo be damaged? Are these parts reliable or may blow up?
4) What is the purpose of the optocoupler in the circuit?
I would really appreciate any help.
I didn't find the 100% schemes for this RCF (400), but found a very similar one (The 600 version).
name and a link here to download the pdf.
DigiPRO600B
https://elektrotanya.com/db-technologies_digipro600b_sch.pdf/download.html
Regards and many thanks
I've this speaker model:
RCF art 415-A.
The power supply is faulty, no votltage out to the amplifier.
The Mosfets are blown. I've changed the mosfets and it's driver, and still have a problem.
I tried to switch on but only one of the mosfets gets hot (the one which switches the 310. There are 2 of them - Mos5 in the scheme).
Obviously I turned it off.
1) What causes it to heat?
2) Testing the VCC of the LMC555, it's only 2.7V. When taking it out of the circuit, it's 12VDC! What makes the voltage to drop. Where does the supply of the LMC555 come from? The VCC of the 555 should be around 10V, as compared with a good card.
I've changed the 555, but the problem remained. I've checked the components around, resistors and capacitors, and transistors, and seem to be OK.
4) The VCC of the Mosfet driver is 10V, but should be 12V if compared with a good card.
3) Could the trafo be damaged? Are these parts reliable or may blow up?
4) What is the purpose of the optocoupler in the circuit?
I would really appreciate any help.
I didn't find the 100% schemes for this RCF (400), but found a very similar one (The 600 version).
name and a link here to download the pdf.
DigiPRO600B
https://elektrotanya.com/db-technologies_digipro600b_sch.pdf/download.html
Regards and many thanks
Sziasztok!
Van egy fenti rádió erősítő a birtokomban. Kérdéseim lennének:
1. Az A és a B hangszórópár csak külön tud szólni? A 4 hangdoboz nem tud együtt?
2. A rádió rész hangolásával lenne kérdésem még mert a 91.1 rádio1 az 91.2 MHz-en jön be. Tehát el van tolódva 0.1 MHz-et.
Kapcsolási rajz meg van a NET-en de abban kérnék segítséget, hogy mely potin tekerjek a rádió panelon hogy ezt korrigáljam.
Köszönettel
Sed3