Service manuals, schematics, eproms for electrical technicians

BRAUN BS37 BATTERY RADIO SCH

AUDIO - SERVICE MANUAL
Type: (PNG)
Size
98.7 KB
Page
---
Category
AUDIO
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar braun manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Please tick the box below to get download link:
  • Also known:
    BRAUN BS-37 RADIO BS37 BATTERY BS 37
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant AUDIO forum topics:
Dynacord Powermate 1000-2 mixer amp fault - Help needed

Hiya
I am repairing a Dynacord Powermate 1000-2 mixer/amp and have a question about DC blocking capacitors in the signal path.

 

I am getting a slowly dropping DC on the DISP1 node (output of I6AA op-amp) on switch-on.  This is causing the green "signal present" LED to come on on that channel which takes about 30 seconds to turn off.  It seems to be caused by a charge on C35A that dissipates slowly through R54A (1M Ohm).  

 

It seems to me, it would have been better to put the C35A on the output of I5AA with a resistor to ground.  Is there a reason why this would not work.  

 

I have checked all relevant components and power supplies and I cannot find any faults but I'm sure this is not normal behaviour.

 

Any help greatly appreciated.

PM1000 tone circuit

signal indicator

 

 

 

Hangváltóba milyen kondenzátort tegyek
Üdv. A jelenlegi hangváltómba bipoláris elkók vannak, de a magas hangok nem a legszebben jönnek ki. Gondoltam a polipropilén kondenzátorra, azzal jobb lehet?

Köszönöm a segítséget!
SP1099F (TDA7088T) TDA2822 felépitett FM vevő nem szól
Hi!
Megtaláltak egy ilyennel.
Beázott, letisztítottam, átforrasztottam elindult, nyektettem 1,5 órát, egyszer kikapcsoltam, majd be, erre nincs hang . Látszólag hangol, mert van hozzá egy kis kijelző, meg adót is talál, de nem szól.
A rádio chip 2 kimenetén kellene lennie HF jelnek?
Mert nincs, de a vég se nagyon akar szólni, hiába érek a 7 pinhez ..
Mi lehet?
TDA7454
Üdvözletem Mesterek !Gyors segítség ! TDA7454 helyet mi jó? Tudom a HQ nál van és nem is drága de nekem most kell megoldanom.Egy lábkiosztás jól jönne. Van 7384 és 86.Betehető helyette? Köszönettel:Öreg Tom :help:
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce