Service manuals, schematics, eproms for electrical technicians

CANON PIXMA IP6210D SM

PRINTER - SERVICE MANUAL
Type: (PDF)
Size
405.5 KB
Page
25
Category
PRINTER
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar canon manual?
Advertisements
Document preview [1st page]
CANON PIXMA IP6210D SM service manual (1st page)
Preview of CANON PIXMA IP6210D SM [1st page]
Click on the link for free download!
Document preview [2nd page]
CANON PIXMA IP6210D SM service manual (2nd page)
Preview of CANON PIXMA IP6210D SM [2nd page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
  • Also known:
    CANON PIXMA IP-6210D IP6210D IP 6210
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant PRINTER forum topics:
Canon iP4500
Üdv! Szervizkönyvet keresek a fenti nyomtatóhoz. A nyomtatófej csatlakozó kiosztásának is örülnék... Köszönöm! sanyika45
Canon rear door sensor
Trying to locate a part number: RC2-2879-000 for a Canon office printer, having no luck. Attached photo of it here.
These use to be rebuildable, where you could snap them open and replace the IR diode and receiver, but not sure if thats still possible.
 
CANON IR1018 DOWNLOADING STANDBY ÜZENET A KIJELZŐN
Tisztelt kolegák,

az irodánk hűséges fénymásolói egyszerre döntöttek úgy, hogy "megtréfáltatnak". Az IR nagyobbik testvére az elkezdte begyűrni a papírt, amikor bekapcsoltam a kistestvért az IR1018-at a címben leírt üzenettel üdvözölt. Milyen letöltésre gondol, nem tudom de már legalább egy évtizede rendessen működött. Anno, megpróbáltam összekötni a PC-vel, hogy nyomtatóként is működjön a W7-en, de ha valamit értelmetlenűl el lehetett komplikálni akkor ezt a CANON IT szakemberei megtették, úgy, hogy a meghatók telepítését feladtam. Szóval, a fénymásoló nincs kötve számítógépre de mégis DOWNLOADING STANDBY. 
Tudna-e valaki a kolegák közűl segíteni?

üdvözletem
CANON Pixma Inkjet MG8120 - error B200
Saw lots of videos on these with error code B200. Cleaning the head seems to solve it many times.
So after I put the cleaned out printhead back in, I did the trick again
where u power it off when the carraige is half way to the left, remove power
andapply power.

This time, it said "processing" on the screen, and the carriage did alot of
extra maneuvers, and looked like it was attempting a cleaning cycle.

At the end, the screen said "cover open", and the carriage slid toward the
left,stopped, and (3) cartridge LED's were flashing slowly, which I was told
meansthose cartriges are low ink. If I closed the cover, the B200 error would
eventually come back.

I asked the customer if he had spare cartridges, and he did, so he bought
them over, we put them in , tried again, and same B200 error.

I told him its likely a print head, and he may try ordering one thru ebay or
something to give that a try. Apparently there are microelectronics inside these
heads? Beats me how they control or regulate ink flow. On the back of the head there are about
50 contact pads, which I guess must be sensors of some kind? He did say he took the head out
at one point, and perhaps ESD may have damaged some sensitive circuitry in
there, and now the head is out of spec.

I thought I saw some russian videos jumpering some of the pads on the head to bypass the code....anyone have any success?


 
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce