Sziasztok!
Hátha valakinek új!
Egy órás-rádió hangja halk, torz. A hangszórón a jel jó,a membrán mozog, és ohmikusan is jó. Szétszedve a következőt láttam: (Csatolmány) A mágnes teljes egészében elporlott, csak a lágyvas korong maradt meg. Ilyet még nem láttam! Lézeregységek mágneseinél láttam már hasonlót, de ott csak néhány szemcse vált le, és szorult be a tekercs és a mágnes közé. Eltávolítva tovább működött.
Üdv
Attila
I greet you! I would need the scheme of this "vintage" amplifier that needs to be "restored". The problem is that in the prefinal and final floor I have many "fried" resistors well, their value cannot be identified.I replaced the defective transistors: 2SC1509, 2SA777,2SB690 and 2SD 796 (each 2 pcs.) and the electrolytic capacitors adjacent to them. I could not go further because of the carbonized resistors that I do not know their value (I can only guess that they are values small, in the order of ohms). The schematic diagram I downloaded, from the address received by the kindness of a colleague is not complete - it is a single page (missing Q29-Q30-Q31-Q3 and resistors R115-R116-R117-R118 which are completely carbonized, at other resistors I could see their value).Thanks in advance!
Finally, I found the missing part
If stuck in the repair and you ask questions, please do it as follows: - Details: Give the exact model number of your device and the chassis ID (if there is). - If possible, please attach pictures of the appliance. - Anamnesis: Write down the exact symptom. If hard to describe the symptom, it is difficult to verbally defined clearly, attach pictures or sound of the phenomenon! - Tell what was you have done so far: search contact error, which parts has examined or changed yet, etc... The incorrectly named topic suspended and will be deleted after 48 hours! Suspended state while others are not able to comment until you correct the address. Subsequent repair of the defective title (within 48 hours) by clicking on the "Edit" tab can be carried out.
Adott egy Onkyo erősítő, melynek a hibája, hogy a kijelzője teljesen sötét, amikor bekapcsolom. Minden más működik rajta, hang is van. Csak a kijelzője nem. Kérem,aki tud az adjon tanácsot,hogy merre induljak el a hibakeresésben. Előre is köszönöm. Csatolok hozzá rajzokat.
Sziasztok!
Segítséget kérnék,mert bevallom elakadtam. Adott ez a masina aminek nincs hangja. Vagyis mikor épp olyan kedve támad, megszólal. NEM érintkezési gond az biztos. Tápfesz rendben, alkatrészek kimérve. Végfok bemenetén.... na ez érdekes. Ellenálláson van jel,(rajz a képen) de az ic felöli oldalról eltűnik mikor épp "hallgatag" a kicsike. Cseréltem az ic-t, naivan annak a hibájára gondoltam. Persze a jelenség nem változott.
Pillanatnyilag nem tudom eldönteni, a feszültség változások miatt jön meg a hang, vagy fordítva. Pl. "7304" (bc847) bázisán 10V mikor van hang, 16v ha nincs.
Ez a "visszacsatolásos táp" megoldás és némítás számomra ismeretlen.
Mivel "zöldfülű" szintről nem tudom lefokozni magam, már elfogytak ötleteim.
Üdv, Z.
A táp ellátásért felelős FET hibája (zárlat) okozta a gondot. Magamtól egyszerűen nem láttam a fától az erdőt, de tanácsot követve (KUMI) hamar kiderült.
KÖSZÖNET érte!