Service manuals, schematics, eproms for electrical technicians
PANASONIC-CT-Z1410LT
Type: 
(E2P)
(E2P)Size
2.1 KB
2.1 KB
Page
---
---
Category
TV
EPROM
TV
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar panasonic manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar panasonic manual?
Document preview [1st page]
No preview item for this file.
Possible causes:
- No preview picture generated yet.
- It is not a pdf file.
Advertisements
Please tick the box below to get download link:
- Also known:
1410 LT PANASONIC CT Z1410LT
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
This elderly monster arrived with the error “ 4 blinks “ which the manual suggests is a power board fault
There are TWO power boards and a standby power board inside
On removing rear cover there were two swollen 220uf caps on the standby board, sadly replacing them the 4 blinks remained
Swapping the two power boards over[ as they look identical , gives a “ 2 Blink “ error , the limited info in the manual suggesting that the fault is on the lower board [ main 2 ]
Both boards have a PFC voltage of around 380 volts at switch on before the relays click out
I have done cold checks on both boards and there are no obvious differences
As the manual has only a block diagram of the power supply it’s difficult to be sure of values / voltages
Has anybody seen or worked one of these or similar beasts and managed to diagnose the problem
Thanks for looking
Regards Ken
There are TWO power boards and a standby power board inside
On removing rear cover there were two swollen 220uf caps on the standby board, sadly replacing them the 4 blinks remained
Swapping the two power boards over[ as they look identical , gives a “ 2 Blink “ error , the limited info in the manual suggesting that the fault is on the lower board [ main 2 ]
Both boards have a PFC voltage of around 380 volts at switch on before the relays click out
I have done cold checks on both boards and there are no obvious differences
As the manual has only a block diagram of the power supply it’s difficult to be sure of values / voltages
Has anybody seen or worked one of these or similar beasts and managed to diagnose the problem
Thanks for looking
Regards Ken
Panasonic TX21JT2P
Keresek a fent nevezett készülékbe Procit,(TDA9361PS/N2/4I1017)Philips IC
A készüléknek nincs hangja,csak egy nagyon pici hangot lehet hallani,végfok IC cserélve,némítás jól működik,ki-be kapcsol,és a hangerő szabályzást persze a proci csinálja.Ha vkinek volna ilyen procija kérem jelentkezzen a
vadaszy@gmail.com email címen!
Hi
I have a Panasonic TH-48LFE8E display in at the moment.
The standby (red) LED does not come on when the power is connected and the unit is not responsive to the remote control.
However when the power button is pressed on the set the green power on LED lights, but there is no backlight or other signs of activity on the LCD.
I have tried to obtain a service manual but apparently they are no longer available?
I have not repaired many Panasonic units and if any one can help it would be appreciated
Stephen Fry
I have a Panasonic TH-48LFE8E display in at the moment.
The standby (red) LED does not come on when the power is connected and the unit is not responsive to the remote control.
However when the power button is pressed on the set the green power on LED lights, but there is no backlight or other signs of activity on the LCD.
I have tried to obtain a service manual but apparently they are no longer available?
I have not repaired many Panasonic units and if any one can help it would be appreciated
Stephen Fry
Sziasztok.
Az a gondom ezzel a szerkezettel hogy nem akar jó szívvel indulni. Ha röviden nyomom a csatorna gombot csak egyet pislog és nem indul. Ha hosszan lenyomva tartom elindul és utána jól megy. Kondikra gyanakodtam de nem igazán jöttem rá a hibára. Valakinek esetleg volt hasonló problémája?
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Reduce