Service manuals, schematics, eproms for electrical technicians
SAMSUNG CK5944N3X
Type: 
(RAR)
(RAR)Size
5.5 MB
5.5 MB
Page
---
---
Category
TV
SERVICE MANUAL
TV
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar samsung manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar samsung manual?
Document preview [1st page]
No preview item for this file.
Possible causes:
- No preview picture generated yet.
- It is not a pdf file.
Advertisements
Please tick the box below to get download link:
- Also known:
SAMSUNG CK5944N3X CK 5944
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Complaint was no display, confirmed and I saw
this series USA model is very prone to backlight failure, so
ordered (8) new strips. Opened up the TV, and am testing the old ones. So
far all the ones on the right side are lighting up ok,
the set of strips connected to them via the connector side with the plugs
are not lighting up at all, even when I supply power directly
to the pins on that side.
I took out a set of the new strips, connected them together and tested, and
they are doing the same thing...whats going on? Thought these were all in
parallel.
If I separate the strips, the one with the connector plug seems to not
light. I have not gone through all the
new ones yet to test. I suppose they could be defective but strange how all
the ones in the TV on that side are not lighting and the others are.
Anyone have an idea whats going on here?
this series USA model is very prone to backlight failure, so
ordered (8) new strips. Opened up the TV, and am testing the old ones. So
far all the ones on the right side are lighting up ok,
the set of strips connected to them via the connector side with the plugs
are not lighting up at all, even when I supply power directly
to the pins on that side.
I took out a set of the new strips, connected them together and tested, and
they are doing the same thing...whats going on? Thought these were all in
parallel.
If I separate the strips, the one with the connector plug seems to not
light. I have not gone through all the
new ones yet to test. I suppose they could be defective but strange how all
the ones in the TV on that side are not lighting and the others are.
Anyone have an idea whats going on here?
Sziasztok!
Első plazma tévé az asztalomon. A készülék poros volt, hűtőbordái nem melegszenek, kondenzátorai nem púposak, A tápfeszültségeket megtalálom, a X és Y panelon 56V-os videojeleket találok a mérőpontokon.
A logic boardon két LED közül az egyik villog, mint a dokumentációban olvasom, de a LED1 csak bekapcsoláskor világít, majd abbahagyja.
Egyenlőre előkerestem a PDP-s leírásokat a 2007-es Műszaki hiba újságból, de jól jönne valami indító ötlet, merre induljak tovább.
Előre is köszönöm!
T.
Első plazma tévé az asztalomon. A készülék poros volt, hűtőbordái nem melegszenek, kondenzátorai nem púposak, A tápfeszültségeket megtalálom, a X és Y panelon 56V-os videojeleket találok a mérőpontokon.
A logic boardon két LED közül az egyik villog, mint a dokumentációban olvasom, de a LED1 csak bekapcsoláskor világít, majd abbahagyja.
Egyenlőre előkerestem a PDP-s leírásokat a 2007-es Műszaki hiba újságból, de jól jönne valami indító ötlet, merre induljak tovább.
Előre is köszönöm!
T.
Tisztelt Fórumlakók !
A címbeli csoda konvergencia hibával került hozzám, persze, előttem már valaki próbálkozott a javításával. A hibrídekhez nem nyúlt, csak a képcsöveket próbálta "beállítani" ( vagy tisztítani, vagy nem tudom mit akart ), és szétcsavarozta az egyiket, ezzel sikeresen kiengedve a hűtőfolyadék egy részét. A lence alatt látszik a légbuborék ( a lencse felülete kb 1/4 részén ), ezért a kép alsó részében zöld homály folt van. Mivel tölthetem fel, vagy van-e valakinek 1 kis ilyen folyadéka?
Köszönöm,
Üdv,
Gondif
Üdv Mesterek!
A fenti masina a nand flash csere után is újraindulgat , de már csak 4-5 percenként. Factory reset megvolt, nem segített.
Szerintetek ?
Üdv.
A fenti masina a nand flash csere után is újraindulgat , de már csak 4-5 percenként. Factory reset megvolt, nem segített.
Szerintetek ?
Üdv.
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Reduce