Service manuals, schematics, eproms for electrical technicians
SONY DSC-F77 FX77 SUPP LEVEL-3 VER-1.2
Type: 
(PDF)
(PDF)Size
21.8 KB
21.8 KB
Page
1
1
Category
STILL CAMERA
INFO-TIPS
STILL CAMERA
INFO-TIPS
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar sony manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar sony manual?
Document preview [1st page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
- Also known:
SONY DSCF-77 DSCF77 FX77 SUPP DSCF 77 FX DSC F77 1.2 DSC-F77
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant STILL CAMERA forum topics:
Sziasztok
Van egy videokamerám a csatolt képen szerepelö eltört alkatrészt keresem,vagy komplett mechanikát.
Tipusa SONY ccd tr 42.
Ez egy régebbi analog kamera,lcd nélkül.
Üdv András
Hello everybody,
Sony CCD TRV-238E camcorder has two issues, first, a wire in the harness( PD-124) is almost cut, which causes bad contact in the LCD panel, I've tried to used a sort of glue to fix it but without success, soldering the two parts is almost impossible ( see picture), the area is too tight.
Second, when the connexion for standard flexible are cut it is possible to scratch the two parts and connect them with extension wire and welding, but in the case of the CONTROL KEY BLOCK's flexible which is used to connect the CONTROL KEY BLOCK to the mainboard, connexions are not made of copper! (carbon maybe, trying to polish will destroy them!), actually, they are worn out (see picture).
Because these spare parts are no longer available in my country, please I need your advice to fix harness and CONTROL KEY BLOCK's flexible.
Sony CCD TRV-238E camcorder has two issues, first, a wire in the harness( PD-124) is almost cut, which causes bad contact in the LCD panel, I've tried to used a sort of glue to fix it but without success, soldering the two parts is almost impossible ( see picture), the area is too tight.
Second, when the connexion for standard flexible are cut it is possible to scratch the two parts and connect them with extension wire and welding, but in the case of the CONTROL KEY BLOCK's flexible which is used to connect the CONTROL KEY BLOCK to the mainboard, connexions are not made of copper! (carbon maybe, trying to polish will destroy them!), actually, they are worn out (see picture).
Because these spare parts are no longer available in my country, please I need your advice to fix harness and CONTROL KEY BLOCK's flexible.
Hi friends,
I would like to make adjustments to my Sony DSC-F717.
According to service manual, the service remote is attached via CPC jig, where a 2,5mm LANC port is mounted. I'd like to DIY a improvised jig.
Exact detail of the jig is not provided, but clearly it is a 22-pin FPC splited into many measure points and a LANC port. Also learned from the manual that LANC signal to/from CPC is splited into 2 lanes, IN and OUT, while 2,5mm LANC port only has 1 (bidirectional) data bus. I wonder if these 2 signals are mixed by additional circuits on the jig.
If someone can post a back (trace-side) photo of CPC12, the mystery will be solved and it will be much appreciated, thanks in advance!
I would like to make adjustments to my Sony DSC-F717.
According to service manual, the service remote is attached via CPC jig, where a 2,5mm LANC port is mounted. I'd like to DIY a improvised jig.
Exact detail of the jig is not provided, but clearly it is a 22-pin FPC splited into many measure points and a LANC port. Also learned from the manual that LANC signal to/from CPC is splited into 2 lanes, IN and OUT, while 2,5mm LANC port only has 1 (bidirectional) data bus. I wonder if these 2 signals are mixed by additional circuits on the jig.
If someone can post a back (trace-side) photo of CPC12, the mystery will be solved and it will be much appreciated, thanks in advance!
Sziasztok!
A fenti kamerához keresek 1-871-287-12 másik szám FP-573 flat cable-t. Ez a kijelzőhöz megy és szakadt. Érdekel bontott, új, vagy beszerzési forrás!
A segítséget előre is köszönöm!
Leiszt Jani
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Reduce