Service manuals, schematics, eproms for electrical technicians

SONY DSC-T1 ADJUSTMENT VER-1.2

STILL CAMERA - SERVICE MANUAL
Type: (PDF)
Size
1.8 MB
Page
71
Category
STILL CAMERA
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar sony manual?
Advertisements
Document preview [1st page]
SONY DSC-T1 ADJUSTMENT VER-1.2 service manual (1st page)
Preview of SONY DSC-T1 ADJUSTMENT VER-1.2 [1st page]
Click on the link for free download!
Document preview [2nd page]
SONY DSC-T1 ADJUSTMENT VER-1.2 service manual (2nd page)
Preview of SONY DSC-T1 ADJUSTMENT VER-1.2 [2nd page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
  • Also known:
    SONY DSCT-1 DSCT1 ADJUSTMENT DSCT DSC T1 1.2 DSC-T1
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant STILL CAMERA forum topics:
SONY-TRV255E
A sony-trv255e kamerám a kijelzőn szüke csíkok vannak. A könyve azt írja koszos a fej.Régebben volt szervízbe,ott is azt írták fejtisztítás. Majd fél év múlva ue. hiba.Félreraktam, vagy két hónap múlva semmi baja. Öt kazetta után megint rossz.Kiváncsi lennék volt e ilyen valakinek,mert csodálkozom a koszos fej magától nem szokott megtisztulni.Azon gondolkozom nem e a mechanika szívat. Érdekelne a véleményetek,érdemes e szétszedni.
Sony DCR-HC14E kamera C 32:30 C 31:30 hibát jelez
Sziasztok! C32:30 és C31:30 hibakódot jelez a kamera. A kazettát nehezen veszi be,/resetelni kell/ bevétel után pörgeti balra aztán jobbra próbálná, de csak hang van fizikailag nem teker ekkor adja a C32.30 hibakódod. A kazetta ajtó kapcsolója eltörött azt helyettesítettem egy nyomógombbal ideiglenesen. Üdv. zaza99
Sony PZ 18-105G SELP18105G missing part
Hello, 

recently bought this lens as "broken/for parts" item. After inspection found there is missing FPC cable, bought one from Aliexpess. Installed it, still not working. After long searching in google was able to find a repair video, that there is seen for a while that there is something with 2-wires in the slot, that is in the photos.  

Here is video at the moment that the part can be seen: https://youtu.be/PjEBGFLjgM0?t=410 (from about 6:50 mins). At 10:44 is seen that the part is only in the bottom side of the slot; and nothing more detailed in the whole internet that I was able to check for about a hour. 

There is magnetic field sensor - top left on the DSC07181 and on the next photo fitted on its place, so I think it should be some kind of tiny end position switch or don't know what;

any help as service manual, photo or part number will be in help.


Regards,

Milen
Anyone has a Sony CPC-12 (J-6082-436-A) service jig?
Hi friends,

I would like to make adjustments to my Sony DSC-F717.

According to service manual, the service remote is attached via CPC jig, where a 2,5mm LANC port is mounted. I'd like to DIY a improvised jig.
Exact detail of the jig is not provided, but clearly it is a 22-pin FPC splited into many measure points and a LANC port. Also learned from the manual that LANC signal to/from CPC is splited into 2 lanes, IN and OUT, while 2,5mm LANC port only has 1 (bidirectional) data bus. I wonder if these 2 signals are mixed by additional circuits on the jig.

If someone can post a back (trace-side) photo of CPC12, the mystery will be solved and it will be much appreciated, thanks in advance!
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce