Service manuals, schematics, eproms for electrical technicians

SONY DSC-U60 ADJUSTMENT VER-1.0

STILL CAMERA - SERVICE MANUAL
Type: (PDF)
Size
321.1 KB
Page
37
Category
STILL CAMERA
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar sony manual?
Advertisements
Document preview [1st page]
SONY DSC-U60 ADJUSTMENT VER-1.0 service manual (1st page)
Preview of SONY DSC-U60 ADJUSTMENT VER-1.0 [1st page]
Click on the link for free download!
Document preview [2nd page]
SONY DSC-U60 ADJUSTMENT VER-1.0 service manual (2nd page)
Preview of SONY DSC-U60 ADJUSTMENT VER-1.0 [2nd page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
  • Also known:
    SONY DSCU-60 DSCU60 ADJUSTMENT DSCU 60 DSC U60 1.0 DSC-U60
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant STILL CAMERA forum topics:
Sony Handycam CCD-tr748E Pinch roller - keresek /MEGOLDVA/
Sziasztok! A fenti csodakamerába keresem ezt a nyomógörgőt! Az imént hozták javításra.. A tulaj új akkut, új kazettát vett bele mert azt hitte így jó lesz:-) Közben kiderült, hogy eme nemes alkatrész elvándorolt valahová a gépből :-) EBAY en találtam, de... csak van valakinek itt a tanyán a fiókban... Köszönöm előre is!
SONY DCR-DVD105 be indul aztán leáll
Szervusztok! Van a fent nevezet kamera,a hiba jelenség.Akkuról indítom a kamerát akkor 1 másodperc múlva ki írja,hogy kéri a DC csatlakoztatót csatlakoztatni és és tölteni. "(USE NEW AC ADAPTER OR REINSERT)" Az érdekesség hogy új akkuval is ezt csinálja de ha hálozatról működtetem akkor minden rendbe van rendesen működik a kamera.Ha ebben tudnátok segíteni azt meg köszönném. Várom a megtisztelő válaszotokat. Üdvözlettel: buszosgyuri! UI. Az akkuk fel vannak töltve!
SONY CCD TRV-238E CONTROL KEY BLOCK
Hello everybody,
Sony CCD TRV-238E camcorder has two issues, first, a wire in the harness( PD-124) is almost cut, which causes bad contact in the LCD panel, I've tried to used a sort of glue to fix it but without success, soldering the two parts is almost impossible ( see picture), the area is too tight.
Second,  when the connexion for standard flexible are cut it is possible to scratch the two parts and connect them with extension wire and welding, but in the case of the CONTROL KEY BLOCK's flexible which is used to connect the CONTROL KEY BLOCK to the mainboard, connexions are not made of copper!  (carbon maybe, trying to polish  will destroy them!), actually, they are worn out (see picture).
Because these spare parts are no longer available in my country,  please I need your advice to fix harness and CONTROL KEY BLOCK's flexible.

 
Anyone has a Sony CPC-12 (J-6082-436-A) service jig?
Hi friends,

I would like to make adjustments to my Sony DSC-F717.

According to service manual, the service remote is attached via CPC jig, where a 2,5mm LANC port is mounted. I'd like to DIY a improvised jig.
Exact detail of the jig is not provided, but clearly it is a 22-pin FPC splited into many measure points and a LANC port. Also learned from the manual that LANC signal to/from CPC is splited into 2 lanes, IN and OUT, while 2,5mm LANC port only has 1 (bidirectional) data bus. I wonder if these 2 signals are mixed by additional circuits on the jig.

If someone can post a back (trace-side) photo of CPC12, the mystery will be solved and it will be much appreciated, thanks in advance!
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce