Service manuals, schematics, eproms for electrical technicians
SONY DSC-W50 SUPP LEVEL3 VER1.2
Type: 
(PDF)
(PDF)Size
39.5 KB
39.5 KB
Page
2
2
Category
STILL CAMERA
SERVICE MANUAL
STILL CAMERA
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar sony manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar sony manual?
Advertisements
Document preview [1st page]
Click on the link for free download!
Document preview [2nd page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
- Also known:
SONY DSCW-50 DSCW50 SUPP DSCW 50 DSC W50 DSC-W50
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant STILL CAMERA forum topics:
Sziasztok!
Olyan gondom lenne a fent nevezett készülékkel, hogy amikor felvételt készítek akkor szakadozik a hang, ill. pixeles lesz a felvétel. De csak akkor ha a kamerát mozgatom ha egy pontra nézek vele akkor nem.
Mi lehet ez?
Üdv Sanyi
Szervusztok!
Van a fent nevezet kamera,a hiba jelenség.Akkuról indítom a kamerát akkor 1 másodperc múlva ki írja,hogy kéri a DC csatlakoztatót csatlakoztatni és és tölteni. "(USE NEW AC ADAPTER OR REINSERT)" Az érdekesség hogy új akkuval is ezt csinálja de ha hálozatról működtetem akkor minden rendbe van rendesen működik a kamera.Ha ebben tudnátok segíteni azt meg köszönném.
Várom a megtisztelő válaszotokat.
Üdvözlettel: buszosgyuri!
UI. Az akkuk fel vannak töltve!
Sziasztok!
Sony service manualt keresek CCU-D50P vezérlőhöz és a CA-D50P kamera dokkhoz, segítségeteket kérem a témához.
Köszi Imre
Hello everybody,
Sony CCD TRV-238E camcorder has two issues, first, a wire in the harness( PD-124) is almost cut, which causes bad contact in the LCD panel, I've tried to used a sort of glue to fix it but without success, soldering the two parts is almost impossible ( see picture), the area is too tight.
Second, when the connexion for standard flexible are cut it is possible to scratch the two parts and connect them with extension wire and welding, but in the case of the CONTROL KEY BLOCK's flexible which is used to connect the CONTROL KEY BLOCK to the mainboard, connexions are not made of copper! (carbon maybe, trying to polish will destroy them!), actually, they are worn out (see picture).
Because these spare parts are no longer available in my country, please I need your advice to fix harness and CONTROL KEY BLOCK's flexible.
Sony CCD TRV-238E camcorder has two issues, first, a wire in the harness( PD-124) is almost cut, which causes bad contact in the LCD panel, I've tried to used a sort of glue to fix it but without success, soldering the two parts is almost impossible ( see picture), the area is too tight.
Second, when the connexion for standard flexible are cut it is possible to scratch the two parts and connect them with extension wire and welding, but in the case of the CONTROL KEY BLOCK's flexible which is used to connect the CONTROL KEY BLOCK to the mainboard, connexions are not made of copper! (carbon maybe, trying to polish will destroy them!), actually, they are worn out (see picture).
Because these spare parts are no longer available in my country, please I need your advice to fix harness and CONTROL KEY BLOCK's flexible.
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Reduce