Service manuals, schematics, eproms for electrical technicians

TELMES TR9901 SERVICE INFO

METER - SERVICE MANUAL
Type: (PDF)
Size
3.8 MB
Page
68
Category
METER
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar telmes manual?
Advertisements
Document preview [1st page]
TELMES TR9901 SERVICE INFO service manual (1st page)
Preview of TELMES TR9901 SERVICE INFO [1st page]
Click on the link for free download!
Document preview [2nd page]
TELMES TR9901 SERVICE INFO service manual (2nd page)
Preview of TELMES TR9901 SERVICE INFO [2nd page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
  • Also known:
    TELMES TR-9901 INFO TR9901 TR 9901
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant METER forum topics:
TELMES Wheatstone mérőhídban lévő hibás középállású galvanométer javítása , kiváltása hogyan? ötleteket várok
Egy TEL-MES Wheatstone mérőhídban hibás a galvanométer, a hiba az, hogy nem mozdul a mutató.A mutatós műszer egy középállású 120 DA házban lévő 30 ohm belső ellenállású Deprez rendszerű. A mérőhíd még nincs nálam, csak tervezem, hogy megveszem, ezért több infót nem tudok róla. Én próbáltam lengőtekercset javítani mikroszkóp alatt de nem sikerült az injekciós tű túl durva volt hozzá és megsértette a 0,0x mm átmérőjű vezeték szigetelését, meg hát ott van a spirálrugó is, tehát nem vállalkoznék még egyszer ilyen mutatványra. Mi lehet baja egy ilyen műszernek, ha nem mozdul a mutató, mennyire valószínű, hogy szakadt a lengőtekercs. Ki lehet-e váltani valahogy sima 120 DA 100uA-os műszerrel( söntölve 31,92 ohm-mal és valahogy előfeszitve 50uA-el hogy középen álljon(lehet hülyeséget írok, de vállalom),mert az van nekem több is. Ha nem lehet kiváltani és nem lehet javítani, akkor hol lehet szerezni ilyen műszert és kb. mennyibe kerül, a Vaterán nem láttam ilyen műszert. Mellékeltem képet a műszerről.
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce