Service manuals, schematics, eproms for electrical technicians
SONY DCR-HC23,24,26,35
Type: 
(ZIP)
(ZIP)Size
10.0 MB
10.0 MB
Page
---
---
Category
CAMCORDER
SERVICE MANUAL
CAMCORDER
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar sony manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar sony manual?
Document preview [1st page]
No preview item for this file.
Possible causes:
- No preview picture generated yet.
- It is not a pdf file.
Advertisements
Please tick the box below to get download link:
- Also known:
SONY DCRHC-23 DCRHC23 24 26 35 DCRHC 23 DCR HC23 DCR-HC23
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant CAMCORDER forum topics:
Sziasztok
Van egy videokamerám a csatolt képen szerepelö eltört alkatrészt keresem,vagy komplett mechanikát.
Tipusa SONY ccd tr 42.
Ez egy régebbi analog kamera,lcd nélkül.
Üdv András
Szép napot
Sony hdr-SR12E kézi kamerán reptéri vizsgálat után nem működik az érintős képernyő persze ez lehet véletlen is mivel repülés előtt ha mozgatva volt a kijelző néha villogott a kép.
1.Szalag kábelre tippeltem kicseréltem a kép oké de érintésre nem reagál
2.Kicseréltem az lcd érintős üveget is de sajnos nem segített
Most a kapcs rajz szerint a Q5901 XP411F-txe Q5902 XP421-txe lehetne talán a hibás de nem biztos
Ha valaki tudna segíteni előre is köszönöm
János
Sony hdr-SR12E kézi kamerán reptéri vizsgálat után nem működik az érintős képernyő persze ez lehet véletlen is mivel repülés előtt ha mozgatva volt a kijelző néha villogott a kép.
1.Szalag kábelre tippeltem kicseréltem a kép oké de érintésre nem reagál
2.Kicseréltem az lcd érintős üveget is de sajnos nem segített
Most a kapcs rajz szerint a Q5901 XP411F-txe Q5902 XP421-txe lehetne talán a hibás de nem biztos
Ha valaki tudna segíteni előre is köszönöm
János
üdv: egyik ismerősöm panaszolja, hogy címbeli kamerája fél órai működés után meleg.
Megmértem, a bal oldala 35 C-fok körül van, az alján az állványcsavarnál 42 fokot mértem egy órai üzem után.
Kérdem, ez elfogadható, vagy hibára utal?
A kamera egyébként normálisan működik.
Bálint
Hi friends,
I would like to make adjustments to my Sony DSC-F717.
According to service manual, the service remote is attached via CPC jig, where a 2,5mm LANC port is mounted. I'd like to DIY a improvised jig.
Exact detail of the jig is not provided, but clearly it is a 22-pin FPC splited into many measure points and a LANC port. Also learned from the manual that LANC signal to/from CPC is splited into 2 lanes, IN and OUT, while 2,5mm LANC port only has 1 (bidirectional) data bus. I wonder if these 2 signals are mixed by additional circuits on the jig.
If someone can post a back (trace-side) photo of CPC12, the mystery will be solved and it will be much appreciated, thanks in advance!
I would like to make adjustments to my Sony DSC-F717.
According to service manual, the service remote is attached via CPC jig, where a 2,5mm LANC port is mounted. I'd like to DIY a improvised jig.
Exact detail of the jig is not provided, but clearly it is a 22-pin FPC splited into many measure points and a LANC port. Also learned from the manual that LANC signal to/from CPC is splited into 2 lanes, IN and OUT, while 2,5mm LANC port only has 1 (bidirectional) data bus. I wonder if these 2 signals are mixed by additional circuits on the jig.
If someone can post a back (trace-side) photo of CPC12, the mystery will be solved and it will be much appreciated, thanks in advance!
Similar manuals:
SONY DCR-DVD110 DVD115 DVD310 DVD410 DVD610 DVD710 DVD810 LEVEL3 VER1.3
SONY DCR-DVD110 DVD115 DVD310 DVD410 DVD610 DVD710 DVD810 SUPP LEVEL2 VER1.2
SONY DCR-DVD110 DVD115 DVD310 DVD410 DVD610 DVD710 DVD810 SUPP LEVEL3 VER1.2
SONY DCR-DVD150E 450E 650 E 850 E LEVEL3 VER1.0
SONY DCR-DVD150 DVD450 DVD650 DVD850 ADJUSTMENT VER1.2
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Reduce