Service manuals, schematics, eproms for electrical technicians

PHILIPS L6.2 REPAIR TIPS

TV - INFO-TIPS
Type: (PDF)
Size
37.8 KB
Page
3
Category
TV
INFO-TIPS
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar philips manual?
Advertisements
Document preview [1st page]
PHILIPS L6.2 REPAIR TIPS service manual (1st page)
Preview of PHILIPS L6.2 REPAIR TIPS [1st page]
Click on the link for free download!
Document preview [2nd page]
PHILIPS L6.2 REPAIR TIPS service manual (2nd page)
Preview of PHILIPS L6.2 REPAIR TIPS [2nd page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
  • Also known:
    PHILIPS L-6.-2 TIPS L6.2 REPAIR
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
PHILIPS 28GR9770/30B
Sziasztok! Van egy PHILIPS 28GR9770/30B TV-m aminek a tápja ki be kapcsol ehhez kellene kapcsolási rajz. Aki tud segíteni,az legyenszíves segítsen. ormi kmero@t-email.hu
Philips ES1E AA hiba
Üdvözletem a Tanyának! A fenti alaplappal szerelt, igen nagy méretű (82cm) 32PW8651/12 készüléket azzal a hibával hozták, hogy a pici gyermek a főkapcsolóval addig játszott (ki-be kapcsolgat), míg teljessé vált az üzemképtelensége. Készenléti LED nem világít, viszont a készenléti tápok megvannak. 5,2V, ill. 9V. Mérhető a 3,2V, és az 1,8V a digitális panelon. ADOC (sajnos BGA) oszcillátora megy, SDA-SCL forgalom természetesen nincs. Már egy kolléga nézte a készüléket, és a digipanelt okolta a hibáért, eddigi méréseim szerint is, az ADOC tűnik a hiba okozójának, segítséget kérek, mi kerülhette el a figyelmem? Ötleteiteket figyelemmel várom, üdv: exGelkás
PHILIPS 25ST2451/10B Ch GR2.2AA képhiba megjavítva
Sziasztok ! Régebben került hozzám a fenti PHILIPS TV azzal, hogy villog a kép, bemelegedés ( kb. egy perc ) után tökéletes. Hűtés és melegítés után a 7331 pozíció számú tranzisztor bizonyult hibásnak, cseréje közben láttam, hogy a C2411 330uF kondi is rossz. Ezeket kicseréltem de nem lett jobb. Most már nem villog de G2 teljesen feltekert állapotában is alig látható a kép a katódok kb. 140-145 V-on vannak. Van-e valakinek ötlete ?
Televisor Philips 32PFL3605/77 enciende realiza un pantallazo parpadea y pantalla queda oscura
Estimados.

El Televisor Philips 32PFL3605/77 LCD tiene una fuente Philips A961A la cual al cunectar el 220v  se quema el fusible . Se procede a controlar la placa  de la fuente y se reemplazo el mosfet  Q602 (transistor en corto), el ic que controla la tensión de entrada (HS01G)  y también se cambio el fusible .
Luego de reemplazar estos componentes se realizo una prueba y el tv encendió, realizo un pantallazo y luego comenzó a parpadear y se se apaga la pantalla. Midiendo tensión en la salida para las lamparas  en los conectores CN2 y CN3 , al presionar el boton de encendido, la tensión es de 97V, el led testigo de la fuente prende y luego comienza a mermar su intensidad lentamente hasta apagarse, la pantalla parpadea y al cabo de unos segundos la tensión en los conectores CN2 y CN3 queda en 18v y la pantalla queda oscura . 

Me pueden ayudar en la reparación , para determinar cual sera el problema que hace que la tensión no se mantenga fija.!
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce