Service manuals, schematics, eproms for electrical technicians
4CM6282
Type: 
(20T)
(20T)Size
256.0byte
256.0byte
Page
---
---
Category
MONITOR
EPROM
MONITOR
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar 4 manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar 4 manual?
Document preview [1st page]
No preview item for this file.
Possible causes:
- No preview picture generated yet.
- It is not a pdf file.
Advertisements
Please tick the box below to get download link:
- Also known:
4CM-6282 4CM6282 CM 6282
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant MONITOR forum topics:
Sziasztok,
idekerült egy ilyen monitor. Az a baj, hogy az OSD néha átvált valami ismeretlen( szerintem nem is létező) nyelvre, melynek következményeként úgy néz ki a képernyő mintha különféle nagyságú négyzetekkel lenne telepingálva. Szerintetek kínozzam üres eeprommal? Vagy nem is eepromhiba?
(Valami szoftverezésről olvastam az előzményekben).
KÖsz.
Üdv.
Tamás
Sziasztok
A mult heten kicsereltem par elkot ebben a monitorban,nem mukodott,a led se gyult ki,ket napig hasznaltam az en sz gepemel.Ma elvitte a kolegam ,Felhivott telefonon hogy ez jelenik meg a kijelzon: Auto config,Please Wait.Azt monja mielott lealt teljesen akkor is ezt irta ki.Mit jelent ez miert irja ki?Holnap hozzak vissza.
Üdv mindenkinek.
Szeretnék egy kis segítséget kérni. Kaptam egy IBM LCD monitort, melynek a kábelját javították. Az egyik fele P&D, a másik DVI-D. Tehát az egyik 30,a másik 24 szálas. Ha valaki tudna segíteni a bekötésbe,azt nagyon szépen megköszönném.Üdv:Suhajda István
This elderly monster arrived with the error “ 4 blinks “ which the manual suggest is a power board fault There are TWO power boards and a standby power board inside.
On removing rear cover there were two swollen 220uf caps on the standby board, sadly replacing them the 4 blinks remained.
Swapping the two power boards over[ as they look identical , gives a “ 2 Blink “ error , the limited info in the manual suggesting that the fault is on the lower board [ main 2 ].
Both boards have a PFC voltage of around 380 volts at switch on before the relays click out, I have done cold checks on both boards and there are no obvious differences.
The manual has only a block diagram of the power supply so it’s difficult to be sure of values / voltages.
My question is has anybody seen or worked one of these or similar beasts
Many thanks Ken
On removing rear cover there were two swollen 220uf caps on the standby board, sadly replacing them the 4 blinks remained.
Swapping the two power boards over[ as they look identical , gives a “ 2 Blink “ error , the limited info in the manual suggesting that the fault is on the lower board [ main 2 ].
Both boards have a PFC voltage of around 380 volts at switch on before the relays click out, I have done cold checks on both boards and there are no obvious differences.
The manual has only a block diagram of the power supply so it’s difficult to be sure of values / voltages.
My question is has anybody seen or worked one of these or similar beasts
Many thanks Ken