Service manuals, schematics, eproms for electrical technicians
52 A063 PS 29RF SAM993X502
Type: 
(HEX)
(HEX)Size
11.3 KB
11.3 KB
Page
---
---
Category
TV
EPROM
TV
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar 52 manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar 52 manual?
Document preview [1st page]
No preview item for this file.
Possible causes:
- No preview picture generated yet.
- It is not a pdf file.
Advertisements
Please tick the box below to get download link:
- Also known:
52 A063 PS 29RF SAM993X502 063 29 RF SAM 993 502
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
I copied the spi flash and nand from a working board of the same model, but it still won't turn on and the standby LED flashes 13 times. Before reprogramming, the LED also flashed and the TV wouldn't turn on. It also wasn't possible to upload software via USB. I read this via UART:
NO
SPI ID:0xEF4015
SPI type:0x01
Spi Su2:0x02
Read back data from SPI....
P:0000
B:1E
sysidx:0CF9
Pwr on:01
RstCode:00000000
last power when ac power: 01
PowerOnEvent: 0x01
Read back data from SPI....
P:0000
B:1E
sysidx:0CF9
Pwr on:00
PowerOnEvent: 0x24
Read back data from SPI....
P:0000
B:1E
sysidx:0CF9
Pwr on:00
PowerOnEvent: 0x24
Read back data from SPI....
P:0000
B:1E
sysidx:0CF9
Pwr on:00
PowerOnEvent: 0x24
Read back data from SPI....
P:0000
B:1E
sysidx:0CF9
Pwr on:00
PowerOnEvent: 0x24
NO
SPI ID:0xEF4015
SPI type:0x01
Spi Su2:0x02
Read back data from SPI....
P:0000
B:1E
sysidx:0CF9
Pwr on:01
RstCode:00000000
last power when ac power: 01
PowerOnEvent: 0x01
Read back data from SPI....
P:0000
B:1E
sysidx:0CF9
Pwr on:00
PowerOnEvent: 0x24
Read back data from SPI....
P:0000
B:1E
sysidx:0CF9
Pwr on:00
PowerOnEvent: 0x24
Read back data from SPI....
P:0000
B:1E
sysidx:0CF9
Pwr on:00
PowerOnEvent: 0x24
Read back data from SPI....
P:0000
B:1E
sysidx:0CF9
Pwr on:00
PowerOnEvent: 0x24
Hibajelenseg: a standby led villog ( szerintem nem hibakod, mindig masmenyit villan).
Az erinto gombokra kozbe-kozbe reagal hangal de se kep se hang, a TV nem kapcsol be.
Tapot fullba ujra kondiztam , kimertem. szerintem az is jo.
(En firmware hibara gyanakszom viszon nem talalok hozza dumpot.)
Minden segitseg jol jon.
Udv. Szilard
Üdvöklök mindenkit!
A cimben leirt tipusu Darfon inverter trafót keresek ami 970 ohm és 3 ohmos 2 darabot, vagy komplett bontott panelt. Egy
névtelen tv-tipusban lakik.
A HQ Electronikánál van 6958L néven olcsón.
Kedves kollégák!
Ez a készülék,bekapcsolás után a logót(bekapcsolási)hang kíséretében feladja,majd megmarad a háttérfény. Ezt a folyamatot háromszor négyszer megismétli,majd nyolcas hibakódot villog. Nem tudom,hogyan lehetne frissíteni,vagy resetelni.
üdv.
Ez a készülék,bekapcsolás után a logót(bekapcsolási)hang kíséretében feladja,majd megmarad a háttérfény. Ezt a folyamatot háromszor négyszer megismétli,majd nyolcas hibakódot villog. Nem tudom,hogyan lehetne frissíteni,vagy resetelni.
üdv.