Service manuals, schematics, eproms for electrical technicians

ACER7154B

MONITOR - EPROM
Type: (ZIP)
Size
402.0byte
Page
---
Category
MONITOR
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar acer manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Please tick the box below to get download link:
  • Also known:
    ACER-7154B ACER7154B ACER 7154
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant MONITOR forum topics:
V7 E17PS
Helló! A fenti készülékkel kapcsolatban szeretnék segítséget kérni. Bekapcsolás után nem indul el, a kép felvillan, majd sötétség. Kb. 5 percnyi ki-be kapcsolgatás után elindul.
Benq GL2450 monitor M240HTN01.2 panel függőleges fehér csík
Sziasztok!

Valószínűleg a control board-on van valami szakadás, hogyan tudom közelebbről behatárolni? Kb 2 pixel széles függőleges világos csík van rajta, ha lehúzom a szalagkábel csatlakozóját, akkor is. Javított már valaki ilyet?

A pozíciójából a képernyőn (kb 1/5-ödénél a teljes szélességnek) lehet a hiba helyére következtetni? Van a panelen 6 db flexkábel ráforrasztva, mindegyik érintkezői megszámozva 1 .... 117. Szemre minden forrasztás jó, az üveg felőli végüket még nem néztem.

Előre is köszönöm,

lcsaszar
AOC lcd monitor fcc id:arstf 1880
:help: Szép napot mindenkinek!A fenti monitorhoz keresek invertert,Tip.:PLCD2417411 vagy valamilyen hasonlót,amivel belehetne indítani.köszönöm.stefi
Fujitsu Siemens Scenicview E24W 24"
Kedves ElektroTanya fórumozók! A hibajelenség az, hogy bekapcsolás után pár másodpercig (kéken világít) próbál bekapcsolni, azután suspend (sárgára vált) Neont meg sem próbálja kapcsolni, kép háttérben nincs. Gépre rakva ua. A tápon 5V és 3,3V megvan, viszont 19V-nak kellene lennie az inverter felé, ez 0V, és 5,3V is 0V. Bekapcsoláskor megjelenik a kapcsoló fesz a tápon, de el is tünik, amikor suspendbe megy. Találkoztatok ilyen hibával, mi lehet a ludas? Nekem tápnak tűnik, de jó lenne javítani. Rajz sajnos nem találtam. A táp száma: fsp100-3p01 Előre is köszönök minden hozzászólást!
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce