Service manuals, schematics, eproms for electrical technicians
BRAUN BATTERIE SUPER-BS40 1939 SCH
Type: 
(PNG)
(PNG)Size
69.1 KB
69.1 KB
Page
---
---
Category
AUDIO
SERVICE MANUAL
AUDIO
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar braun manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar braun manual?
Document preview [1st page]
No preview item for this file.
Possible causes:
- No preview picture generated yet.
- It is not a pdf file.
Advertisements
Please tick the box below to get download link:
- Also known:
BRAUN BATTERIE SUPERBS-40 SUPERBS40 1939 SUPERBS 40 SUPER BS40 SUPER-BS40
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant AUDIO forum topics:
Üdv Mesterek!
Keresem az alábbi autós erősítő kapcsolási rajzát/Hellfire HL-5.13/ de főleg a táp rajza érdekel, amit TL 494 IC és MC 4558 IC/által fetek hajtják meg. TL 494 adatlapja letöltve.
Hibája a következő: Protect bemenetre 12V feszt kapcsolva a táp néha elindul, de többször nem. Az IC-k megkapják a tápot TL 494-es, előállítja az 5v-os referencia feszt. Táp kondik, IC-k kicserélve, forrasztási hibák megszüntetve. Ha a táp fel áll, minden csatornája jó. Vagyis nem a végfok fogja a tápot. 494-es IC 74khz oszcillál. Segítségeteket előre is köszönöm.
További szép estét. proci
Buongiorno. L'amplificatore come da titolo inserendo un segnale dai rispettivi ingressi in uscita non si sente nessun suono. Le tensioni allo stadio finale, servite da transistori sono corrette. ho notato che anche nella cuffia non si sente l'audio. Potreste per favore darmi qualche suggerimento in merito? Grazie.
Given:
Victor TT-71, neon lamp does not light, speed is lower than normal. This is subsequent some short circuit the owner does inside the device. No further details.
I found out the VICTOR QL7 have the same motor driver amd I downloaded the service manual that I attached here in case this manual is not already uploaded.
Looking at the diagrams I found out that at TP3 (same with pin5 of IC803) instead if that rectangular signal, I have nothing but 5VDC and a negative or positive short spike whenever I'm starting or stopping the motor and
Under the circumstances I suspect IC803 is defective. The bad thing, IC803 is NPC SC8043. Also I wonder if the crystal is fine (except that I wonder what can be wrong with a crystal after some short circuit).
Does anybody have any more suggestion?
Also, where can NPC SC4043 be sourced? Also, a crystal 9.054MHz?
Thanks in advance,
Corneliu
Victor TT-71, neon lamp does not light, speed is lower than normal. This is subsequent some short circuit the owner does inside the device. No further details.
I found out the VICTOR QL7 have the same motor driver amd I downloaded the service manual that I attached here in case this manual is not already uploaded.
Looking at the diagrams I found out that at TP3 (same with pin5 of IC803) instead if that rectangular signal, I have nothing but 5VDC and a negative or positive short spike whenever I'm starting or stopping the motor and
Under the circumstances I suspect IC803 is defective. The bad thing, IC803 is NPC SC8043. Also I wonder if the crystal is fine (except that I wonder what can be wrong with a crystal after some short circuit).
Does anybody have any more suggestion?
Also, where can NPC SC4043 be sourced? Also, a crystal 9.054MHz?
Thanks in advance,
Corneliu
Jó reggelt, Shalom Sabbath! Kérdés a címben. Bekapcs, köszön, F61 és magától kikapcs. Tudja é Valaki mi a nyűgje?
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Reduce