Service manuals, schematics, eproms for electrical technicians

CANCA 2157LT

TV - EPROM
Type: (RAR)
Size
969.0byte
Page
---
Category
TV
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar canca manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Download free of charge (10 files / day):
Download is being processed. Please wait...
Download processing...
  • Also known:
    CANCA 2157LT 2157 LT
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Sencor SLE 2909m4 képhiba
Sziasztok!
A Sencor SLE 2909m4 képhibában (kontraszt jellegű) kérnék segítséget.
Bekapcsoláskor néha fél órán belül előjön a képhiba. Telekomos DTV MPEG4 kódolású adás. Ha a kihúzom a koax-ot vagy csatornát váltok megjavul.Izolátort is tettem semmi változás főleg a RTLKLUB adásnál (266MHz 6875kS/s jelsebesség 256QAM moduláció).( Idén februárban távirányítót nem érzékelte- tápszűrő 16ohm lett.) Pontos rajzot nem találtam és nagyon integrált a panel.
A segítséget előre is köszönöm!
Képek:
Mitsubishi HC4000 DLP projector PCGC8 ver.2 software required
PCGC8 ver.2 software required with any possible firmware for a Mitsubishi HC4000 DLP projector..Does anyone have the software please?
TV Videoton C2911-AM Plat : nem indul = MEGOLDVA
Tisztelt Fórumlakók! A címben szereplő ( Sasszé: A1 ? ) csak annyit tudott hogy STBY Led pirosan világít, +3,3V van, +13 felezve, így sem +8 , sem +5 nem jó, +B: 65V körül ( de lehet hogy Stby-on így is kell?? ). I2C korrupt volt, eepromot átírtam, ezzel a Led villog ( pirosan), +13V pulzál 7V körül. Ha leakasztom a TDA 3951PS/N3/3 -ról a +8 V-ot ( 2 közül egyiket), sorkimenő beindul, minden fesz ok, de csak szürke raszter, semmire nem reagál, Led zöld. Van-e valakinek jobb ötlete a TDA cserénél? S ha jobb ötlet nincs, van-e valakinek ilyen procija? A matrica a TDA-n: PR FM 2,2 bt . Köszi! Üdv, Gondif
Philips 21PT1532/58H - táp nem indul
Üdvözlet mindenkinek! Adott ez a készülék, ami táp hibával került hozzám. A Graetz híd, a MOSFET, a 6502 jelű zener, a 6514 zener mind zárlatos volt, cseréltem őket. A 7501-es tranyó (BF487) szintén cserére szorult, MPSA44-et tettem a helyére, és a biztonság kedvéért cseréltem a 2115-ös kondit is. A probléma, hogy egyáltalán nem indul be a táp, a félvezetőket, ellenállásokat mérve hibát nem találok, 96V helyett csak 5V-ot mérek. Megköszönném az iránymutatást merre tovább, mert tanácstalan vagyok...
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce