Service manuals, schematics, eproms for electrical technicians
CANON PIXMA IP1100 1800 2500 SERVICE RESET PROGRAM
Type: 
(RAR)
(RAR)Size
191.0 KB
191.0 KB
Page
---
---
Category
PRINTER
OTHER
PRINTER
OTHER
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar canon manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar canon manual?
Document preview [1st page]
No preview item for this file.
Possible causes:
- No preview picture generated yet.
- It is not a pdf file.
Advertisements
Please tick the box below to get download link:
- Also known:
CANON PIXMA IP-1100 RESET PROGRAM IP1100 1800 2500 IP 1100
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant PRINTER forum topics:
Köszöntök Minden Tanyakedvelőt !
Címben jelzett Canon Pixma MP450 nyomtatóhoz Win10 64 bit-hez keresek drivert. Ebben kérek segítséget, mert az én próbálkozásaim nem vezettek eredményre.
Címben jelzett Canon Pixma MP450 nyomtatóhoz Win10 64 bit-hez keresek drivert. Ebben kérek segítséget, mert az én próbálkozásaim nem vezettek eredményre.
Sziasztok!
A fenti nyomtató patron csere után B200 hibakódot jelez.
Ismeri valaki?
Hellótok!
A tárgybéli nyomtató szabályos távolságonként (fekete: 27,5 mm/13,25 mm; sárga:26 mm) vizszintesen csíkoz.
A Transfer unit és a fekete toner már cserélve volt.
Csatolok egy képet (Kicsit gyűrött a szállítás miatt. :)
Van esetleg valamilyen ötletetek?
A Laser egységre gondolok, de mielőtt szétszedném, jó lenne a megerősítés.
Köszönettel.
A tárgybéli nyomtató szabályos távolságonként (fekete: 27,5 mm/13,25 mm; sárga:26 mm) vizszintesen csíkoz.
A Transfer unit és a fekete toner már cserélve volt.
Csatolok egy képet (Kicsit gyűrött a szállítás miatt. :)
Van esetleg valamilyen ötletetek?
A Laser egységre gondolok, de mielőtt szétszedném, jó lenne a megerősítés.
Köszönettel.
Saw lots of videos on these with error code B200. Cleaning the head seems to solve it many times.
So after I put the cleaned out printhead back in, I did the trick again
where u power it off when the carraige is half way to the left, remove power
andapply power.
This time, it said "processing" on the screen, and the carriage did alot of
extra maneuvers, and looked like it was attempting a cleaning cycle.
At the end, the screen said "cover open", and the carriage slid toward the
left,stopped, and (3) cartridge LED's were flashing slowly, which I was told
meansthose cartriges are low ink. If I closed the cover, the B200 error would
eventually come back.
I asked the customer if he had spare cartridges, and he did, so he bought
them over, we put them in , tried again, and same B200 error.
I told him its likely a print head, and he may try ordering one thru ebay or
something to give that a try. Apparently there are microelectronics inside these
heads? Beats me how they control or regulate ink flow. On the back of the head there are about
50 contact pads, which I guess must be sensors of some kind? He did say he took the head out
at one point, and perhaps ESD may have damaged some sensitive circuitry in
there, and now the head is out of spec.
I thought I saw some russian videos jumpering some of the pads on the head to bypass the code....anyone have any success?
So after I put the cleaned out printhead back in, I did the trick again
where u power it off when the carraige is half way to the left, remove power
andapply power.
This time, it said "processing" on the screen, and the carriage did alot of
extra maneuvers, and looked like it was attempting a cleaning cycle.
At the end, the screen said "cover open", and the carriage slid toward the
left,stopped, and (3) cartridge LED's were flashing slowly, which I was told
meansthose cartriges are low ink. If I closed the cover, the B200 error would
eventually come back.
I asked the customer if he had spare cartridges, and he did, so he bought
them over, we put them in , tried again, and same B200 error.
I told him its likely a print head, and he may try ordering one thru ebay or
something to give that a try. Apparently there are microelectronics inside these
heads? Beats me how they control or regulate ink flow. On the back of the head there are about
50 contact pads, which I guess must be sensors of some kind? He did say he took the head out
at one point, and perhaps ESD may have damaged some sensitive circuitry in
there, and now the head is out of spec.
I thought I saw some russian videos jumpering some of the pads on the head to bypass the code....anyone have any success?