Service manuals, schematics, eproms for electrical technicians

CP14K40

TV - EPROM
Type: (E2P)
Size
664.0byte
Page
---
Category
TV
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar cp manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Please tick the box below to get download link:
  • Also known:
    CP-14K-40 CP14K40 CP 14 40
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
40PFL4707 Philips logo and shutsdown
Dear Expert
The details of my TV is as follows

1. Philips 40PFL4707/F7 Manufactured March 2012
2. SMPS Board BA21P6F01 01 1
3. SMPS board has a sticker that says A21P6MPW C 7219720
4. This is a 110v Mains Supply TV sold in USA
5. I imported this from USA into my country where we have 230V.
6. I have a simple winding transformer that converts 230v to 110v

The TV has been having this problem.  Here are the steps
1. Mains power on
2. Front panel white led blinks 6 times
3. Philips logo display
4. TV shuts down immediately
5. Nothing happens.  If i press power button on TV or remote nothing happens
6. Have to power off and then wait for few minutes to experience same repetition.

Last two days, tried several times, only once the TV started and after 10 minutes it did auto shutdown as there was no input signal connected.

Does this indicate issues with SMPS or main cpu board ? Even if its faulty, how did it start once ?

More testing done as follows
1. Removed all connectors. Cleaned all three pcb with liquid cleaner. Cleaned all connectors externally and internally ( holes) using painting brush. Allowed everything to dry.
2. Reconnected
3. Started. This time, went past the Philips logo. I could connect a macbook via HDMI and play youtube videos on the TV for ~1 hours.
4. Using remote, entered service mode and initialized ( factory reset) the TV
5. For 1 hours of proper run, measured voltages. LED+24v was showing properly at 24v, AL+3.3v was at proper 3.3v and the P-ON-H1 was properly at 3.3v
6. After about 1 hrs, the screen shut down. The LED+24v is showing at 6v, AL+3.3v at 3.3v and P-ON-H1 is a 0v. This indicates the main cpu board has turned off the P-ON-H1 signal.
7. Power off, wait for 2 min. Power on... same philips logo and TV shuts down. Problem repeats.
8. Firmware is Code TVNB010_00_PF_XX91_BA PIC code U10_CM08:_40A_C7W_R_02. Did a google search and found no references if this firmware needs any upgrade.

requesting experts next steps to root cause the issue. I suspect the main board is bad and the SMPS is good. What if I manually put a wire from AL+3.3v to P-ON-H1 ? will the TV be on or is it risky for the main cpu board ?

I am attaching the service manual for this TV
Grundig CUC1935 Nem indul a táp. ( Kész )
Sziasztok! Most került hozzám ez a gép, nem megy a tápja. A piros LED sárgára vált, és ennyi, a sorvégtranzisztor átvezetett de a csere után sincs változás. A 300V meg van, fet kimérve jónak tűnik, a táp ic ( TDA16846 ) mellette lévő kondi cserélve, ellenállások jók. Készenléti tápok 3,3V 12V rendben, a távval kapcsolva a LED villog, de kikapcsolni nem lehet. Mit nem veszek észre, valamelyik opto miatt nem indul?
Egy technisat HD26-tv-hez a main beazonositására kérnék segitséget megoldva(chassis-mst9u19b)
Szevasztok van egy Technisat lcd tv-m ,amely main hibás,de nem ismerem az alaplapját,ebben szeretnék a kollégáktól segitséget kérni,hogy fényképek alapján hátha valaki beazonositja az alaplapot,kérésem megismételve üdv:lali "FONTOS! Olyan fórum téma nevet válassz, ami beszédes, minél pontosabban illeszkedik arra, amivel kapcsolatban írsz. Egy lehetséges jó elnevezés pl: ORION LCD PT26S chassis 17MB12-2, a tápja nem indul Az nem elég, hogy pl: "LG LCD-TV" vagy "HP laptop" és hasonlóak. Illetve érdektelen, nem releváns információt se tartalmazzon a cím! A helytelenül elnevezett topik felfüggesztésre, majd 48 óra után törlésre kerül! Felfüggesztett állapotban nem tudnak mások addig hozzászólni, amíg ki nem javítod a címet. A hibás cím utólagos javítása (48 órán belül) a "Szerkesztés" fülre kattintva végezhető el."
SONY KD55X9305C tuner gond
Sziasztok! Ismét egy érdekes hibához kérném segítségeteket. A készülékkel DVB C  kábeltévés adást vesznek ,és a probléma a következő. Bekapcsolásnál  sok esetben,főleg ha hosszu ideig ki volt kapcsolva a készülék,akkor kiírja hogy nincs jel.Hiába váltanak másik csatornára ,ott  sincs,holott a kábelhálózat jó.Ha a menüben az "ujrainditás" opciot alkalmazzák akkor bejön a kép és tökéletes,nem pixeles stb.Utána  ha ki be kapcsolják továbbra is jó,de másnap már nem biztos,ilyenkor megint ujra kell inditani a softvert.Ami érdekes ,ezt azota csinálja ,miota lefrissitette magát a netről a tv ,mert azelőtt jó volt.USB-ről próbáltam rátenni a legujabb softvert de azt írja ,hogy naprakész a tv. Gyári beállítás ,ujrahangolást próbáltam.
Tud esetleg valaki valami tippet erre,mert én kifogytam az ötletekből.

Köszi

Lalee
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce