Service manuals, schematics, eproms for electrical technicians

CTX1785S

MONITOR - EPROM
Type: (ZIP)
Size
337.0byte
Page
---
Category
MONITOR
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar ctx manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Please tick the box below to get download link:
  • Also known:
    CTX-1785S CTX1785S CTX 1785
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant MONITOR forum topics:
Monitor táp elko csere - MEGOLDVA
Sziasztok! Előszőr kezdek neki lcd monitor javításnak, tanácsokat várok. Hiba: bekapcsoláskor 1-2 másodpercig van kép aztán elmegy a led világít. Tápegység elkok-nak cserélésével kezdeném, már kiszedtem őket. Ami benne volt: - 4db 1000uF 25V GF(M) U1A 105C 8 (gyári leírás szerint: Impedance 0.035 Ripple Current 1900) - 2db 470uF 25V GF(M) U1A 105C 8 (gyári leírás szerint: Impedance 0.060 Ripple Current 1210) - 1db 220uF 25V GF(M) U1A 105C 8 (gyári leírás szerint: Impedance 0.130 Ripple Current 640) - 2db 150uF 25V GF(M) U1A 105C 8 (gyári leírás szerint: Impedance 0.130 Ripple Current 640) Az lenne a kérdésem, hogy helyettesítésnél mennyire kell figyelni az impedancia és erre a Ripple értékre? Helyettesítőnek találtam hasonló értékű kondikat, csak az a baj, hogy egyik sorozatban sincs meg az összes kapacitás érték. 1. Rubycoon ZLJ sorozat 25V 105C 1000 uF Impedance 0.028-0.084 Ripple Current 2500 470 uF Impedance 0.053-0.16 Ripple Current 1700 220 uF nincs ebből a sorozatból 150 uF Impedance 0.17-0.51 Ripple Current 700 2. Rubycoon ZL sorozat 25V 105C 1000 uF Impedance 0.021-0.053 Ripple Current 2360 470 uF Impedance 0.038-0.12 Ripple Current 1430 220 uF Impedance 0.072-0.22 Ripple Current 760 150 uF nincs ebből a sorozatból mi a különbség a két széria között, kombinálhatom-e a kettőt illetve hol tudnék megfelelőkondikat venni, elég-e csak a kapacitás-feszültség-hőm hármas értéket figyelni, vagy az impedancia, ripple fezs. is fontos? Van egy másik lcd monitor is aminek vibrál a képe, ott merre induljak el a hiba kereséssel. Előre is köszönöm a segítséget. Üdv: Misi
Samsung UE43TU7172 dupla kép/sor
Üdv Mindenkinek!

A fenti TV duplázza a képtartalmat a kijelző egy részén. Még nincs nálam a TV, csak tájékozódom hogy esetleg a szalagkábel kitakarásos módszer segíthet? 
LM004 REV:3 monitortáp, inverter panel hiba
Sziasztok Amatőr kérdéseimre szeretnék válaszokat. Milyen esetekben tilt le egy inverter, hogyan lehet ezt kikapcsolni(pl. ha leddel világítanám meg, vagy csak kevesebb csővel, amíg tudok hozzá csövet szerezni),rajz híján persze. Megkondiztam, a trafók jók. Köszi Jani
Monokrom CRT monitor pótlása LCD monitorral.
Üdvözlet Mindenkinek!
CORGHI kerék centírozó gép monokrom CRT monitora tönkrement. Kéznél van egy 17"-os TFT-LCD monitor, ezt szeretné a tulaj beépíttetni.
 Kérdés, hogyan csatlakoztassuk a régi monitor video- és szinkron jeleit az LCD monitor VGA kábeléhez.A mellékelt kép mutatja a monitorra dugaszolható PCB aljazatot a gépről érkező vezérlő vezetékekkel. Az 1. és 7. a +/- 12 V, a 2,3,4 egy külső 100 kOhmos potméterről jön (single turn... ? ), a 6-zöld, 8-fehér, 9-piros, 10-sárga vezetékek hozzák a szinkront- H,V -  és a video jelet. 
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce