Sziasztok!
A tévé nem ad hangot. Egyik bemenetről sem. Letöltöttem a szervizkönyvet, és
" Service Modes, Error Codes, and Fault FindingEN 12 TCM2.0E LA5.
5. Service Modes, Error Codes, and Fault Finding
Index of this chapter:
5.1 Test Points
5.2 Service Modes
5.3 Error Codes
5.5 Service Tools
5.1 Test Points
This chassis is NOT equipped with test points in the service
printing. No test points are mentioned in the service manual.
5.2 Service Modes
The Service Mode feature is split into different parts:
• Service Alignment Mode (SAM).
• Service Default Mode (SDM).
• Customer Service Mode (CSM).
SDM and SAM offer features, which can be used by the Service
engineer to repair/align a TV set. Some features are:
• Activates the blinking LED procedure for error identification
when no picture is available (SDM).
• Make alignments (e.g. white tone), (de)select options,
enter options codes, reset the error buffer (SAM).
• Display information (“SAM” indication in upper right corner
of screen, error buffer, software version, options and option
codes, sub menus).
The CSM is a Service Mode that can be enabled by the
consumer. The CSM displays diagnosis information, which the
customer can forward to the dealer or call centre. In CSM
mode, “CSM”, is displayed in the top right corner of the screen.
The information provided in CSM and the purpose of CSM is to:
• Increase the home repair hit rate.
• Decrease the number of nuisance calls.
• Solved customers' problem without home visit.
5.2.1 Service Alignment Mode (SAM)
How to Enter
To enter SAM, use the following method:
• Press on the remote control the code “062596” directly
followed by the “INFO” key.
After entering SAM, the following screen is visible, the values
can be adjusted according to the requested (see Chapter 8"
Szóval a saját távirányítóján az INFO gomb helyén időzítő óra jele látható. Ha beütöm a 062596 kódot, az első két szám után jön az üzenet, hogy nincs ilyen csatorna, de ha nem hagyom abba, és végig nyomom a 6 számjegyet, majd az INFO gombnak megfelelőt. (Megkerestem a képét a NET-en) akkor sem lép be.
Van valakinek ötlete, vagy más kódja?
Előre is köszönöm!
T.
Hello !
Kaptam egy ilyen TV-t. Tegnap TV-nézés közben "kihúnyt" a képe, csak a hang maradt.
Ma meg már csak villog a STBY LED-je...
SPI Flash tartalom cserével talán megmenthető lenne, de ilyet még sosem csináltam.
Az USB-s "recovery" rátöltésével megpróbálkoztam, úgy tűnik a LED "pislogása" alapján, mintha rendben lezajlana, de semmi változás.
Honnan lehetne ehhez a
két IC-hez konkrét eeprom tartalmakat letölteni ?
A Tanyán csak ennek a 40" TV-ét találtam meg:
"technika_17mb82_40col_904a_dled_fhdss14"
Milyen néven/címen kellene keresnem?
Remélem akad valaki, aki tud segíteni...
CÍMKEAZONOSÍTÓK:
Mainboard: 17MB82S
Fehér cimkén: 10098509 23238977.... 32"
LCD panel: VES315WNDL 2D-N02
Üdv.:Uniman
Időközben még erre leltem: http://elektronline.hu/wwwboard/thread.php?sorszam=735027&reply=5
Segítség kellene egy tranzisztort kellene cserélnem de nem kapható és nem tudom mivel helyettesítsem,
2SD2599N ami bedöglött és nem tudom mit merjek helyette bele rakni.
Jó reggelt Mindenkinek! Készenléti van, indításkor egy másodpercig sor és képeltérítés indul, majd egy másodperc múlva leáll. Ha egyfolytában nyomom a csatornaváltó gombot, akkor indul, megáll. Végül jobb ötletem nem lévén, csipesszel rövidre zártam a procon a "bus" és órajel lábakat, nos azóta megy. De mi lehetett a baja?????