Service manuals, schematics, eproms for electrical technicians
HEATHKIT ID-29 AUTO TEST INSTRUMENT SCH
Type: 
(GIF)
(GIF)Size
43.5 KB
43.5 KB
Page
---
---
Category
OTHER
SERVICE MANUAL
OTHER
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar heathkit manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar heathkit manual?
Document preview [1st page]
No preview item for this file.
Possible causes:
- No preview picture generated yet.
- It is not a pdf file.
Advertisements
Download free of charge (10 files / day):
Download processing...
Download processing...
- Also known:
HEATHKIT ID-29 TEST INSTRUMENT ID29 AUTO ID 29
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant OTHER forum topics:
Sziasztok!
Keresek ilyen packot.
1300mAh
50*37*17 mm
70g
Hol lehet ilyet, vagy csak egy cellát ehhez szerezni.
Köszi
Sziasztok,üdv itt lesz egy pár kínai töltő elektromos járműhöz biciklihez
Sziasztok mesterek !
A gyermekem keresett meg azzal , hogy itt a Tanyán kérdezzelek meg benneteket,
kinek van és milyen tapasztalata a fenti szerkezetekkel.
Ablak csere előtt állnak, akkor már nem szeretnék kifúrni az új ablak keretet, de
redőny is kellene.
Tehát :
1., Ajánlott típus ? Olasz , Amerikai , stb.
2., Szerviz igény ? Havonta , évente , esetleg több évente ?
3., Az Alumínium és a műanyag közötti előny hátrány ? Főszempont a hangszigetelés !!
4., Külső belső tokozás előny , hátrány ?
5., Egyenkénti /ablakonként / vagy több csatornás távirányító ?
Szívesen vennék minden tapasztalatot , ha megosztanátok velünk !
Köszönet mindenkinek az esetleges tapasztalatok átadásáért előre is !
Working on a speed charge battery maintainer for small engines battery. Heat sink had (2) S2025R T0-220 type components on it. Seems they are an SCR and I have 57 ohms on 1 and 3 pin, so seem they are short. Cant get these anymore but installed S4025R which seems to be better replacement. Before replacing, heat sink seemed to be really hot after replacng on on
board 10 amp automotive slot type fuse, so seemed these SCR were bad, getting hot woth no load.
Standby LED not lighting with new SCR's installed. Old ones did not have heat sink compound on them, so I used some to better transfer heat. I saw the input of the 7805 1 amp
regulator IC has short, so removed it, and its not shorted, but the feed to it comes from the IC chip on board, a EM78P41 BWD20J. Data sheet for EM78P41 is online. They have pin 16 going to pin 1 of the 7805 regulator. Actual reading on pin 16 to ground is 2.5 ohms. I suspect this IC is shorted output. Is there chance to replace IC or is this repair finished?
board 10 amp automotive slot type fuse, so seemed these SCR were bad, getting hot woth no load.
Standby LED not lighting with new SCR's installed. Old ones did not have heat sink compound on them, so I used some to better transfer heat. I saw the input of the 7805 1 amp
regulator IC has short, so removed it, and its not shorted, but the feed to it comes from the IC chip on board, a EM78P41 BWD20J. Data sheet for EM78P41 is online. They have pin 16 going to pin 1 of the 7805 regulator. Actual reading on pin 16 to ground is 2.5 ohms. I suspect this IC is shorted output. Is there chance to replace IC or is this repair finished?
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Reduce