Service manuals, schematics, eproms for electrical technicians
HT-580-26LA59 26TA02
Type: 
(PDF)
(PDF)Size
210.7 KB
210.7 KB
Page
1
1
Category
TV
SERVICE MANUAL
TV
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar ht manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar ht manual?
Document preview [1st page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
- Also known:
26TA02 HT 58026 LA 59 26 TA 02 580 26LA59
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Hi
got the red flashing standby light,2 blinks
tried power off,with power button hols,and reboot,but no luck.
I guess board has fault,not sure where to start on checking board for fault
any help appreciated
ta
got the red flashing standby light,2 blinks
tried power off,with power button hols,and reboot,but no luck.
I guess board has fault,not sure where to start on checking board for fault
any help appreciated
ta
Sziasztok ! A készülék DVB-T 1-2 tunerrel rendelkezik ! A box amit a MINDIG TV szolgáltatótól kaptak a fizetős csatornák vételéhez elfelejti a csatornabeállításokat ez lehet box hiba ? A CI+ csatalakozó az mire használható azon kívül hogy CF kártyákat fogadjon vagy netalán CONAX dekódert ?
Szerény véleményem szerint nem szabadna elfelejteni a csatorna beállításokat mivel ez egy hétvégi ház és áramtalanítva van természetesen akkor amikor nem tartózkodnak ott , rendkívűl bosszantó minden alkalommal újrahangolni a készüléket ! Várnám véleményeteket !
Szerény véleményem szerint nem szabadna elfelejteni a csatorna beállításokat mivel ez egy hétvégi ház és áramtalanítva van természetesen akkor amikor nem tartózkodnak ott , rendkívűl bosszantó minden alkalommal újrahangolni a készüléket ! Várnám véleményeteket !
Szép mosolygos napot mindenkinek,Sziasztok.
Kis segitséget kérek.
Ki ismeri a belépési kodot a jelzett Philips Hotel TV-nél.
Továbá a service menübe.
Mod: 20HT3253/58. Shassi : L9H.2E
Köszönöm
Manufacturer: Panasonic
Type: TX-L42ETW5
Chassi: LA35
Hello everybody,
I could determine or measure the following with the device:
Device does not start anymore, stand-by LED lights red when device is plugged in and flashes red as soon as an IR command (key press) is sent via the remote control. Voltages of power supply STB 5V and signal LCD_TV_SUB_ON come from A-board. Power supply starts, supplies P15V and SUB1.1V, 1.5V, 1.8V, 3.3V, 5V, HDMI3.3V and USB5V are generated on the A-Board (stand for about 2.5 seconds). Then signal LCD_TV_SUB_ON goes low (voltages go away to STB 5V) and after about 2 seconds back to high (endless). What is missing is the voltage PNL12V which is switched on by PANEL_VCC_ON2. PANEL_VCC_ON2 always has a low signal and does not change its state. Power supply also provides for the 2.5 seconds the 24V for the backlight. Clocking of LCD_TV_SUB_ON starts immediately after plugging in the mains plug (also without IR command). SOS error code is not output. The over-voltage circuit in IC 5000 pin 7 also does not respond. Attached is the timing diagram from the technical training of Panasonic where I have drawn until when the boot process behaves normally.
In my opinion a mistake on the A-board? Does anyone have a tip?
greetings
Andi
Type: TX-L42ETW5
Chassi: LA35
Hello everybody,
I could determine or measure the following with the device:
Device does not start anymore, stand-by LED lights red when device is plugged in and flashes red as soon as an IR command (key press) is sent via the remote control. Voltages of power supply STB 5V and signal LCD_TV_SUB_ON come from A-board. Power supply starts, supplies P15V and SUB1.1V, 1.5V, 1.8V, 3.3V, 5V, HDMI3.3V and USB5V are generated on the A-Board (stand for about 2.5 seconds). Then signal LCD_TV_SUB_ON goes low (voltages go away to STB 5V) and after about 2 seconds back to high (endless). What is missing is the voltage PNL12V which is switched on by PANEL_VCC_ON2. PANEL_VCC_ON2 always has a low signal and does not change its state. Power supply also provides for the 2.5 seconds the 24V for the backlight. Clocking of LCD_TV_SUB_ON starts immediately after plugging in the mains plug (also without IR command). SOS error code is not output. The over-voltage circuit in IC 5000 pin 7 also does not respond. Attached is the timing diagram from the technical training of Panasonic where I have drawn until when the boot process behaves normally.
In my opinion a mistake on the A-board? Does anyone have a tip?
greetings
Andi
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Reduce