Service manuals, schematics, eproms for electrical technicians

HT7

MONITOR - EPROM
Type: ()
Size
1024.0byte
Page
---
Category
MONITOR
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar ht manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Download free of charge (10 files / day):
Download is being processed. Please wait...
Download processing...
  • Also known:
    HT-7 HT7 HT
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant MONITOR forum topics:
Planar PT1503N LCD monitor nem kapcsol be.
Sziasztok! A fenti külső tápos monitor semmilyen életjelet nem ad. Megkapja a tápot, a belső két 3,3V-s stabilizátor működik és ennyi. Hiába nyomkodom a bekapcsoló gombot semmi sem történik. Van a sarokban egy kapcsolt táp de az nem indul. Találkozott már valaki ilyen hibával? Üdv.
Scaleoview C19-4 (Model 900P)
sziasztok kaptam egy siemens-kipukkant tápú monitort ,eleinte a megnyitott és bezárt ablakok láttszottak még jó darabíg a monitoron...aztán pukkant benn valami(elmondás alapján)ehhez keresek rajzot vagy szervízmanuált.köszi Csaba
Samsung 171T monitor DP502T táp IC helyettesítési gondok [MEGOLDVA]
Sziasztok! Szétszállt az 5 lábú DP502T IC mert felfujódott a 100uF/400V, nem lehet beszerezni, igy helyettesitenem kellett. Talaltam egy orosz oldalon FSDM07652RB-vel megoldást (ez 6 lábu). -kiiktatva a 2x270k -pin5 nem bebötve -1uF kidob és 75k beköt pluszra. -még 1 db 1N4148 (2. kép módositás-logikátlan) De nekem terheletlenül 5V helyett 4,65V van, a másik feszültség 12,6V. Bekapcsolva leesik 3,3V-ra a másik meg 6-7V ra, és pulzál is. Külön 5V-ot adtam, akkor mukodik a scaler LED is világít. Tehát csakis a tápegység hiba van. A 3. lábon 11-15Vig ugrál a táp IC táplálása. Cseréltem TL431-et, optokoplert, Sec. elkók ESR-re jók, primer 33uF-akat már valaki cserélte (22uF+10uF), mérve azok is jók. Trafó lábai nem szakadtak. 75k helyett 68k/2W-t tettem , de nem hiszem hogy az számit. Rajz nincs a SM-ban
LG W1946S-BF monitor vízszintes fehér csíkok, majd lassan eltünnek
Sziasztok! Bekapcsoláskor 90%-a képernyônek tele vízszintes csíkokkal, majd lassan fogynak a csíkok és kb 5 perc múlva tökéletes a kép. De mihelyt rezolucióváltás (vagy kikapcs-bekapcs) azonnal csíkos megint csak most gyorsabban fél perc alatt eltünnek. Fújtam meleggel-hütöttem is a scalert meg a t-cont de nem érzékeny rá. Van 2db próba lcd panelem, de nem barátkozik egyik sem ezzel scalerrel (függôleges oszlopok lesznek), így nem tudom t-con vagy scaler lapon keressem a hibát. Hôlégfuvoval atfujtam mindent de szerintem nem kontakthiba lehet, az elkókat ESR-rel mind átmértem és mind jó. Probáltam müködés közben kihuzni a flet kábelt ami a scalert összeköti a t-connal, és azonnal visszadugtam de egybôl csíkos jelenség lett. Igy a t-conra gondolok, de nem vagyok benne biztos hatha csak valami adatmegszakadás miatt ujraindul a scaler.
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce