Service manuals, schematics, eproms for electrical technicians

MARCONI VALVE MANUAL 1928

OTHER - OTHER
Type: (PDF)
Size
21.8 MB
Page
68
Category
OTHER
OTHER
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar marconi manual?
Advertisements
Document preview [1st page]
MARCONI VALVE MANUAL 1928 service manual (1st page)
Preview of MARCONI VALVE MANUAL 1928 [1st page]
Click on the link for free download!
Document preview [2nd page]
MARCONI VALVE MANUAL 1928 service manual (2nd page)
Preview of MARCONI VALVE MANUAL 1928 [2nd page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
  • Also known:
    MARCONI VALVE 1928
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant OTHER forum topics:
Injektor csatlakozó tipusa????
Szép napot mindenkinek. Van egy Chevrolet Aveom 12-s 2008-as kiadás.Keresem a mellékletben csatolt Injektor csatlakozó tipusát.Honnén lehetne beszerezni, mert a legnépszerübbek között nem találom, a tipusát sem . Elöre köszönöm válaszotokat Üdv és továvvi szép napot András
Kone uniswing door operator - seeking schematics / service manual
Hi everyone.
I'm trying do fix a door operator (Kone Uniswing Operator) for a public association which takes care of disabled people.
It mainly consist in a dc motor powered through a full H bridge and controlled by a single chip 16 bit microcomputer (M16C/62P family)
First investigations show that the motor is ok, power rails are clean and micro computer does not seem to be fried (correct control of the 1 digit display)

I have to look deeper and therefore  desperately looking for schematics and service manual

If someone could help me it would be deeply appreicated

ps : the little story. The maintenance guy from Kone came and after a while said that nothing could be done except replacing the door operator by a new one : 3000 Euros ! (the complete door had been purchased 4 years ago for 4000 Euros)

Thanks by advance

pf


ultrhangos szépítő kipróbálásában kérek segítséget
hi. egy ALVEOLA B388a tip ultrahangos szépítő javításában kérnék segítséget. vagyis főleg a kipróbálásban... a készülék kezelő részen működik, lehet szabályozni az időt és energiát, de a kimeneti rca aljzaton nem mérek semmit--bár nem tudom mit kellene mérnem.. van hozzá egy -régi brg mikrofonhoz hasonlító-fej ami 2 vezetékkel csatlakozna az rca aljzathoz. bekapcsoláskor a relé kapcsol,de más jelenség nincsen. a fej első ránézésre nemigen szétszedhető-roncsolni nem akarom.. tudja valaki,hogy hogyan kellene dolgoznia?? Üdv: egon loviegon@t-online.hu 30-9 986 575
Tecpel DCM2606 multimeter lehet hogy hibás?
Sziasztok!
Kaptam egy ilyen műszert ajándékba.
Sajnos lehet van némi gond is vele, (ajándék lónak ne nézd a fogát!) Ohm mérésnél, folytonosság mérésnél elég érdekes anomáliát látok. "400.0" jelenik meg az lcd-n, a "4" karakter ütemesen villog, viszont mérni tudok vele. Pontosan méri amit kell.
A másik anomália az dióda mérésnél tapasztaltam.
Amint dióda mérésre kapcsolom a műszert akkor az LCD-n "3.172V" jelenik meg.
Ennél is ugyan az a jelenség hogy mérni lehet, S jól is mér. Ilyenkor szerintem "OL" felirat kellene legyen. Na adj isten rosszul gondolom?
Aki tud ebben segíteni kérem tegye meg.
Szeretném ezt a műszert fel éleszteni. Nem szeretném ha a kukában végezné.
Szét bontva nem látok rajta hibás alkatrészt, rá mérve, már amit tudtam azok jók. 
Mérései is pontosak, csak nekem furcsa ez a fajta vissza jelzés.
​​​​​​
Üdv Istvan78!
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce