Üdv!
Lenne ez ketyere .
Nincs életjel, a stby led nem ég.
Az V+5,6VSt eljut az előlapra, ill. a ebből a feszből levő V+5VH megvan a procin.
Nem ülteti meg a proci ezt a feszt.
A gombok jónak tűnnek. A procit átforrasztottam, de semmi..:(
A 49. oldaltól taglalja az előlapot:
https://elektrotanya.com/pioneer_vsx-1015-k,s_sm.pdf/download.html
Halott lenne chip......?
Kösz
This is a compact design to I guess transfer the vinyl into MP3 format.
Complaint was when the arm was moved the tt dont spin, confirmed that as
theres a leaf switch to sense arm movement,
and its fed to a main pcb with all the IC's that I guess handle all the
stuff. The switch is ok, and I remember seeing 14V or so on the motor pins
frm the PCB, so I figured perhaps theres anough current to spin the motor and
focused on testing the motor.
Manufacturer does not supply the mainboard that feeds the motor but
the motor can be taken apart and after I opened it and
disconnected the small pcb fron the motor terminals and apply power
directly, it spins w 12v. theres a small electrolytic cap on the pcb 25V / 22uF and an
AN6652 4 pin T0-220 type case IC that I guess is some kind of speed control
circuitry.
The drive Motor is an EG-530-SD-3F, main board is stamped K-13007.
Gonna check the cap, but after searching this IC and its
applications with the motor, I see its popular and some drawings show how its used to regulate the 78,33
and 45 rpm speeds.
This drawing looks pretty much what I see in there:
https://tectronelectronics.eu/images/thumbnails/465/465/detailed/31/eg530.jpg
I have replaced the IC and the cap, but the motor still does not turn. The main pcb
is proprietary and cant be purchased, and I think it is giving the op-amp IC a reference signal.
Is there a way to bypass that signal or fool the IC to believing its on to test it out?
Photo showing the motor pcb :
http://www.mediafire.com/view/s79blgku1503mtg/HPIM0643.JPG/file
Photo of motor under test:
http://www.mediafire.com/view/thhgvcwac8al7gu/HPIM0635.jpg/file
Sziasztok, van egy pioneer VSX-418 tip házimozi erősítőm, amit hibásként vettem. Nekiláttam a hibakeresésnek, a standby tápon kívül nem működött semmi, bekapcsolni sem lehetett, tehát tényleg halottnak látszott. Minden nap keresgéltem, és találtam is jónéhány hibát, kontakt, zárlatos és szakadt alkatrészek. Ezek javítása után a gép már majdnem teljesen működő volt, de mivel a D+5v tápját ideiglenesen kellett adnom a stabilizátor panelről, ami a hűtőbordán van (a saját ic-je is hibás volt), egy véletlen folytán a krokodilcsipesz lecsúszott az átkotésről, és persze odatalált a 12v-ra... Most ott tartok kb. Mint az elején. Látszólag a D+5v körök rendben vannak. Jelenleg itt tartok :
- az AC_WUP folyamatosan 3.3voltot ad, tehát behúz a táptrafó relé, minden feszültség megvan
- a védelmi körök magas szinten vannak (4,8v), dcdet, ovldet, xprotect, de csak ha a kijelző panelt nem csatlakoztatom a szalagkábelével, amint rádugom eltűnik ez a 3 magas szint a syscom 72,73,89 lábairól. A táptrafó relé viszont nem kapcsol le!
Most már 2hete szenvedek vele, jó lenne kideríteni hogy menthető - e, ebben szeretnék segítséget kérni nálam ilyen téren jártasabb szakiktól!
Köszönöm szépen előre is!
Sziasztok!
Megkértem Kolya kollegát, hogy fordítsa le nekem a BEAG EBE5312-es (nem sokban különbözik az 5310-től) gépkönyvét oroszról magyarra. Az eredmény ezennel közhírré tétetik.