Service manuals, schematics, eproms for electrical technicians
PANASONIC-TX28WG25C
Type: 
(RAR)
(RAR)Size
1.5 MB
1.5 MB
Page
---
---
Category
TV
SERVICE MANUAL
TV
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar panasonic manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar panasonic manual?
Document preview [1st page]
No preview item for this file.
Possible causes:
- No preview picture generated yet.
- It is not a pdf file.
Advertisements
Download free of charge (10 files / day):
Download processing...
Download processing...
- Also known:
28 WG 25 PANASONIC TX28WG25C
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Tiszteletem Mindenkinek!
Fentebb említett TV-hez képernyőt keresek, illetve ha nem találok, akkor bontásra ajánlom...
Eredetileg indításkor a 10-es hibakódot villogta, a logikai panelről az 5, és a 3,3V tápfeszültség hiányzott. Javítása után készülék rendben elindult, de kiderült, hogy a képernyőn, némely COF is gatya volt, hiányzott a kép jobb oldala... :(
Fentebb említett TV-hez képernyőt keresek, illetve ha nem találok, akkor bontásra ajánlom...
Eredetileg indításkor a 10-es hibakódot villogta, a logikai panelről az 5, és a 3,3V tápfeszültség hiányzott. Javítása után készülék rendben elindult, de kiderült, hogy a képernyőn, némely COF is gatya volt, hiányzott a kép jobb oldala... :(
Fenti masinába keresnék kijelzőt. Típusa: LC320WXN LG display
Kedves mesterek!
Van egy Panasonic TX-L32EM6B LED-es LCD TV. Bekapcsoláskor 3 alkalommal megjön a fény a kép és a hang 3-4 másodpercre, és kikapcsol. Azután a piros jelző LED egyeket villog. A hiba táblázat szerint a LED meghajtó inverter a hibás. Cseréltem a tápegység modult, ezen van a led meghajtás is. A hiba továbbra is megvan. Amikor rendesen működik, a tápegység modulon a BL-1 lábon 4.5V van. A harmadik próbálkozás után nem kap többet feszültséget. A main-board lehet hibás? Ha igen, belerakhatom helyette ezt: Panasonic TX-L42B6B MAIN AV BOARD TNP4G548 1 A Az eredeti TNP4g548 1 A, de ez a TV 32-es.
Köszönet e lőre is.
M.
kekestv tipje bejött!
Egy LED volt hibás. Csere után minden rendben.
Köszönettel!
Hi
I am having trouble finding any information regarding this product.
The unit powers up and the output is displayed on the screen for between 0 and ten seconds, the unit then powers down, the red standby LED on the front of the unit blinks then remains off for 5 seconds then blinks again.
This cycle continues until the power is disconnected, if the power is reconnected the unit goes back in to stand by (red led steady) it will then power on again.
Also in the error mode (red led blinking) and the power button on the back of the unit is pressed twice it will power up but this does not happen if the remote is used.
I have tested various capacitors and diodes but all seems well, I have also replaced the power supply with a reconditioned unit but this has not helped.
I have been unable to obtain any service information for this product.
So any input would be most helpful.
Thank you
Stephen Fry
I am having trouble finding any information regarding this product.
The unit powers up and the output is displayed on the screen for between 0 and ten seconds, the unit then powers down, the red standby LED on the front of the unit blinks then remains off for 5 seconds then blinks again.
This cycle continues until the power is disconnected, if the power is reconnected the unit goes back in to stand by (red led steady) it will then power on again.
Also in the error mode (red led blinking) and the power button on the back of the unit is pressed twice it will power up but this does not happen if the remote is used.
I have tested various capacitors and diodes but all seems well, I have also replaced the power supply with a reconditioned unit but this has not helped.
I have been unable to obtain any service information for this product.
So any input would be most helpful.
Thank you
Stephen Fry
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Reduce