Service manuals, schematics, eproms for electrical technicians

PANASONIC TX-25V30X

TV - EPROM
Type: (RAR)
Size
317.0byte
Page
---
Category
TV
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar panasonic manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Download free of charge (10 files / day):
Download is being processed. Please wait...
Download processing...
  • Also known:
    PANASONIC TX-25V-30X TX25V30X TX 25 30 25V30X TX-25V30X
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Panasonic TX-P42G20E Chassis GPF13DE (4.hibakód)
Sziasztok! Panasonic TX-P42G20E,bekapcsolás után nem indul.A LED zölről porosra vált,illetve 4 villan ,vár ismét 4 villan és igy tovább.A hiba a P modul hibájára utal.Érdekelne ,nem találkoztatok-e esetleg ezzel a gonddal és ha igen mi lenne az orvoslása.A válaszokat előre is köszi. "FONTOS! Olyan fórum téma nevet válassz, ami beszédes, minél pontosabban illeszkedik arra, amivel kapcsolatban írsz. Egy lehetséges jó elnevezés pl: ORION LCD PT26S chassis 17MB12-2, a tápja nem indul Az nem elég, hogy pl: "LG LCD-TV" vagy "HP laptop" és hasonlóak. Illetve érdektelen, nem releváns információt se tartalmazzon a cím! A helytelenül elnevezett topik felfüggesztésre, majd 48 óra után törlésre kerül! Felfüggesztett állapotban nem tudnak mások addig hozzászólni, amíg ki nem javítod a címet. A hibás cím utólagos javítása (48 órán belül) a "Szerkesztés" fülre kattintva végezhető el."
Panasonic Plasma TH-85PF12E Error code " 4 Blinks "
 This elderly monster arrived with the error “ 4 blinks “ which the manual suggests is a power board fault

There are TWO power boards and a standby power board inside

On removing rear cover there were two swollen 220uf caps on the standby board, sadly replacing them the 4 blinks remained

Swapping the two power boards over[ as they look identical , gives a “ 2 Blink “ error , the limited info in the manual suggesting that the fault is on the lower board [ main 2 ]

Both boards have a PFC voltage of around 380 volts at switch on before the relays click out

I have done cold checks on both boards and there are no obvious differences

As the manual has only a block diagram of the power supply  it’s difficult to be sure of values / voltages

Has anybody seen or worked one of these or similar beasts and managed to diagnose the problem 

Thanks for looking 

Regards  Ken 
panasonic tx29 ps12
Sziasztok!A fent nevezett készülék két áramszünet után a következőket produkálja.A főkapcsoló bekapcs után villog a piros led az elején.Rajzom már van,de minden ötletet szívesen fogadok. Üdv:Geri
Panasonic TH-42PX80E plazma TV nem indul (valtozott, indul, de beteg)
Sziasztok
Van nalam egy ilyen TV:
Panasonic TH-42PX80E plazma TV
A PFC reszben levo Q406 FET tranzisztor zarlatos volt, a tipusa RJK5010
Ki volt egve  a halozati reszen F401 es F402 biztositek, a tipusa T8AH
Az D401 egyeniranyito hidban zarlatos volt 2 dioda. A hid tipusa a rajta levo jeloles szerint D6SB 80 a rajz szerint B0FBAT000006 (800V/6A)

Ezeket csereltem es meg meregettem a TV-ben de nem talaltam mas hibat.
Csere utan ugy tunt, hogy valami csattant uzembe helyezeskor. Aramtalanitottam es meregettem benne, de minden jo volt.
Utana ismet bedugtam es megfigyeltem a LED-eket.
Amikor aramot kap, a piros LED 10-et pislog. Ez a F_STB +15V vagy valamelyik belole eredo feszultseg hianyat jelenti.
Ha megnyomoma bekapcsolo gombot, pislog a zold LED, de utana ismet 10 piros pislogas.
A kovetkezokre jottem ra:
A STB5V megvan, betapolja a maint, az megadja 15 masodpercig a F_STB_ON feszultseget (3.2V), de F_STB (+15V) nincs.
Tovabb meregetve rajottem, hogy a R448 es R449 teljesitmeny ellenallasok ( 0.12 Ohm/5W) ami a tapot csatolja, szakadtak.
Most jon a kerdesem:
Szerintetek ezek is ki voltak egve amikor elszallt a Graetz, a biztositekok es a FET, vagy pedig van valami zarlat amit nem talaltam meg, es most szallt el? Merve a cserelt alkatreszek most jok.
Elore is koszonok minden velemenyt, minden jot,

Janos
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce