Service manuals, schematics, eproms for electrical technicians

PANASONIC TX-28MD3P

TV - EPROM
Type: (RAR)
Size
509.0byte
Page
---
Category
TV
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar panasonic manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Please tick the box below to get download link:
  • Also known:
    PANASONIC TX-28MD-3P TX28MD3P TX 28 MD 28MD3P TX-28MD3P
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Panasonic TX-42P2E (ch: GPH13DE) plasm 13-at villog, nem kapcsol be
Üdv!
A címben említett plasma a fenti hibajelenséget produkálja. A meglévő SM csak 12-es kódot ír, igy nem igazán tudom az okát. Mérve, már amit lehet minden ok. Y-sus, Z-sus probára cserélve, helyzet ugyan az.
atti1
Pioneer plazma PDP-LX5090(panasonic belső?) nem indul, 11 villogás. (megoldva)
Sziasztok!
Nagyon nem kedvelem a plazmákat, mégis egy ilyet javítanék. Ismerősöm elmondás szerint, (miután hozzá került) egyszer beindult, többé soha. Átmérve hamar kiderült, nem dolgozik a PFC. Most már stabil 400v megvan. Bekapcsolást követően minden feszültség megjön, majd kb. 2 másodperc után kikapcsol és 11 villogás...  elvileg ez ha jól tudom ventilátor (meg sem moccannak) hibára utalna. Minden a négy kifogástalan, nem szorul. Külső tápról 12 volton 60mA az áramfelvétel. Próbáltam lekövetni miként is vezérelné őket, de elakadtam.  Lenne valakinek tippje mi lehet a gond, vagy tévútra vittem magam ezzel a venti dologgal? 
Köszönettel: Kiss Z.
Panasonic TX-L42s20e-hez eeprom tartalmat MAIN AV BOARD TNP8EA106 8A
Sziasztok. Tudna valaki segíteni eeprom tartalom miatt. Rengeteg típushoz találtam de ehhez semmit. Napokat szántam rá de semmi. Előre is köszönöm. Üdv.M
Panasonic TX-L42ETW5 Device does not start anymore, stand-by LED lights up red, no SOS error code
Manufacturer: Panasonic

Type: TX-L42ETW5

Chassi: LA35



Hello everybody,

I could determine or measure the following with the device:

Device does not start anymore, stand-by LED lights red when device is plugged in and flashes red as soon as an IR command (key press) is sent via the remote control. Voltages of power supply STB 5V and signal LCD_TV_SUB_ON come from A-board. Power supply starts, supplies P15V and SUB1.1V, 1.5V, 1.8V, 3.3V, 5V, HDMI3.3V and USB5V are generated on the A-Board (stand for about 2.5 seconds). Then signal LCD_TV_SUB_ON goes low (voltages go away to STB 5V) and after about 2 seconds back to high (endless). What is missing is the voltage PNL12V which is switched on by PANEL_VCC_ON2. PANEL_VCC_ON2 always has a low signal and does not change its state. Power supply also provides for the 2.5 seconds the 24V for the backlight. Clocking of LCD_TV_SUB_ON starts immediately after plugging in the mains plug (also without IR command). SOS error code is not output. The over-voltage circuit in IC 5000 pin 7 also does not respond. Attached is the timing diagram from the technical training of Panasonic where I have drawn until when the boot process behaves normally.

In my opinion a mistake on the A-board? Does anyone have a tip?

greetings

Andi
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce