Sziasztok! Vettem egy ilyen TV-t, hogy a téli sporteseményeket, jó minőségben nézhessem.(UPC műholdas HD box van)Iszonyú képet ad, ha fehér a kép. Ocsmány, piszkosszürke a hó, vagy a jégkorong pálya, ráadásul kegyetlenül villog ahogy koriznak ide-oda, mert az elektronika pont azon a határon van, hogy leszabályozgatja a túl nagy fehéreket.Nézhetetlen.Panás kollégáktól kérdezném, hogy nem lehet-e szervíz menüben(beléptem, de nem állítottam semmin) valamit állítani, vagy egyszerűen kikapcsolni ezt az "automatikát"?
(a villanyszámla nem gond)
A barátom is ilyet vett és pontosan ez a jelenség nála is. Ha nincs sok fehér a képtartalomban, akkor verhetetlen a képminőség. Köszi előre is a válaszokat, üdv.
I got a broken Panasonic that will not start. It does show the red front LED and the power supply delivers 5,3Volt standby. Only when you try to start by remote or push button on the set it will only flash the red LED and does nothing more.
After a while, the red LED will start to flash repeatedly 13 times.
Since the 5,3 Volt standby run straight to the main board I wanted to check there but no luck finding the schematics.
Any insights?
After several attempts the TV finally started and I could enter the menu screen. Normal functionality. But after switch off it takes again several attempts. What is going on ?
Üdv a tisztelt Kollégáknak!
A fenti monstrummal lenne egy kis gondom. A hiba amivel hozták, hogy a kép bemákosodik. Előszőr csak kb 1 óra után csinálta de mikor idekerűlt akkor már csak fél percet bírt. Teljesen elmegy a képe, de nem elhangolódik mert finom hangolással se lehet beállítani ezután.
Szerintem olyan mintha agc problémája lenne. Valakinek van valami tapasztalata?
UI: Tunert cseréltem benne de nem változott a helyzet.
Köszönöm Zoli
Sziasztok
Van nalam egy ilyen TV:
Panasonic TH-42PX80E plazma TV
A PFC reszben levo Q406 FET tranzisztor zarlatos volt, a tipusa RJK5010
Ki volt egve a halozati reszen F401 es F402 biztositek, a tipusa T8AH
Az D401 egyeniranyito hidban zarlatos volt 2 dioda. A hid tipusa a rajta levo jeloles szerint D6SB 80 a rajz szerint B0FBAT000006 (800V/6A)
Ezeket csereltem es meg meregettem a TV-ben de nem talaltam mas hibat.
Csere utan ugy tunt, hogy valami csattant uzembe helyezeskor. Aramtalanitottam es meregettem benne, de minden jo volt.
Utana ismet bedugtam es megfigyeltem a LED-eket.
Amikor aramot kap, a piros LED 10-et pislog. Ez a F_STB +15V vagy valamelyik belole eredo feszultseg hianyat jelenti.
Ha megnyomoma bekapcsolo gombot, pislog a zold LED, de utana ismet 10 piros pislogas.
A kovetkezokre jottem ra:
A STB5V megvan, betapolja a maint, az megadja 15 masodpercig a F_STB_ON feszultseget (3.2V), de F_STB (+15V) nincs.
Tovabb meregetve rajottem, hogy a R448 es R449 teljesitmeny ellenallasok ( 0.12 Ohm/5W) ami a tapot csatolja, szakadtak.
Most jon a kerdesem:
Szerintetek ezek is ki voltak egve amikor elszallt a Graetz, a biztositekok es a FET, vagy pedig van valami zarlat amit nem talaltam meg, es most szallt el? Merve a cserelt alkatreszek most jok.
Elore is koszonok minden velemenyt, minden jot,
Janos