Service manuals, schematics, eproms for electrical technicians
PHILIPS20GX1656
Type: 
(E2P)
(E2P)Size
664.0byte
664.0byte
Page
---
---
Category
TV
EPROM
TV
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar philips manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for similar philips manual?
Document preview [1st page]
No preview item for this file.
Possible causes:
- No preview picture generated yet.
- It is not a pdf file.
Advertisements
Please tick the box below to get download link:
- Also known:
PHILIPS 20 GX 1656
- If you have any question about repairing write your question to the Message board. For this no need registration.
- If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
Have a nice Day! - See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Helló!
Ez egy kis lcd tv dvd kombóban. A tulaj elmondás szerint néha elindul és néha nem. Nos 1 hét járatás után most egyáltalán nem megy. A stby led átvált, ( ez az álapot csak pár mpig van így aztán újra stby) de nincs sem hang sem kép, de még háttérvilágítás sem. Lámpával megvilágítva nem látszik semmi a kijelzőn. Csöveit cseréltem, tápokat rendben találtam, tápban kondikat kicseréltem és semmi.
Köszi, üdv.: Ízirájder
Sziasztok
A fenti szutyok reggelre megbolondult.Kikapcsolásra demozik,önállóan programot vált hangol,hangerőt változtat.Hasonló trükkökkel szórakoztat.A gombsort és egyebeket már kiirtottam belőle.Memoria,vagy proc?
Köszönöm!
Sziasztok!
Sony KD-55x8005 C Tv.folyamatosan ujra indul.Nem reagál se távra ,se kezelőegységre.Megjelenik a Sony felirat ,majd leáll ,és ujra indul.Táp jónak tűnik.Internet szerint Androidos a tv ,bár ugyanakkor ezek más logóval indulnak az Android verziótól függően.Gugli szerint resetelni kéne ,de nem tudom.
Kérek segítséget!Üdvözlettel Reparator
Sony KD-55x8005 C Tv.folyamatosan ujra indul.Nem reagál se távra ,se kezelőegységre.Megjelenik a Sony felirat ,majd leáll ,és ujra indul.Táp jónak tűnik.Internet szerint Androidos a tv ,bár ugyanakkor ezek más logóval indulnak az Android verziótól függően.Gugli szerint resetelni kéne ,de nem tudom.
Kérek segítséget!Üdvözlettel Reparator
Screenshots of problem here in the post.
Picture of screen with both cables to panel from TCON connected, and the other is with one side disconnected.
I have read the cables from the TCON to the display loosen up on the end to the panel. I believe as I am working on moving the cables around, the picture is improving
and getting clearer. So I think thats the problem. Someone mentioned using tape over them to hold them to the panel better. I have not taken the metal frame off to
look at them, but there is a narrow gap where I read some people stuff cardboard in there to press down on them better.
Has anyone ever seen this issue and come up with a good way to resecure the cables?
Picture of screen with both cables to panel from TCON connected, and the other is with one side disconnected.
I have read the cables from the TCON to the display loosen up on the end to the panel. I believe as I am working on moving the cables around, the picture is improving
and getting clearer. So I think thats the problem. Someone mentioned using tape over them to hold them to the panel better. I have not taken the metal frame off to
look at them, but there is a narrow gap where I read some people stuff cardboard in there to press down on them better.
Has anyone ever seen this issue and come up with a good way to resecure the cables?