Sziasztok!
A tévé nem ad hangot. Egyik bemenetről sem. Letöltöttem a szervizkönyvet, és
" Service Modes, Error Codes, and Fault FindingEN 12 TCM2.0E LA5.
5. Service Modes, Error Codes, and Fault Finding
Index of this chapter:
5.1 Test Points
5.2 Service Modes
5.3 Error Codes
5.5 Service Tools
5.1 Test Points
This chassis is NOT equipped with test points in the service
printing. No test points are mentioned in the service manual.
5.2 Service Modes
The Service Mode feature is split into different parts:
• Service Alignment Mode (SAM).
• Service Default Mode (SDM).
• Customer Service Mode (CSM).
SDM and SAM offer features, which can be used by the Service
engineer to repair/align a TV set. Some features are:
• Activates the blinking LED procedure for error identification
when no picture is available (SDM).
• Make alignments (e.g. white tone), (de)select options,
enter options codes, reset the error buffer (SAM).
• Display information (“SAM” indication in upper right corner
of screen, error buffer, software version, options and option
codes, sub menus).
The CSM is a Service Mode that can be enabled by the
consumer. The CSM displays diagnosis information, which the
customer can forward to the dealer or call centre. In CSM
mode, “CSM”, is displayed in the top right corner of the screen.
The information provided in CSM and the purpose of CSM is to:
• Increase the home repair hit rate.
• Decrease the number of nuisance calls.
• Solved customers' problem without home visit.
5.2.1 Service Alignment Mode (SAM)
How to Enter
To enter SAM, use the following method:
• Press on the remote control the code “062596” directly
followed by the “INFO” key.
After entering SAM, the following screen is visible, the values
can be adjusted according to the requested (see Chapter 8"
Szóval a saját távirányítóján az INFO gomb helyén időzítő óra jele látható. Ha beütöm a 062596 kódot, az első két szám után jön az üzenet, hogy nincs ilyen csatorna, de ha nem hagyom abba, és végig nyomom a 6 számjegyet, majd az INFO gombnak megfelelőt. (Megkerestem a képét a NET-en) akkor sem lép be.
Van valakinek ötlete, vagy más kódja?
Előre is köszönöm!
T.
Sziasztok.
Szeretnék újra egy kis segítséget kérni.
PHILIPS 28 PT 450A/00 TV-hez keresek rajzot,vagy segítséget.
Csíkba össze ugrott a kép. / nem az enyém /
Adás be jön, hang van.
Ha valaki tud segíteni,azt most 9is nagyon megköszönném.
Hali.Szenvedek már három napja evvel a csoda géppel a helyzet a sortrafó csatogot gajra vágta a tda8362e 4x ict, a függ ict meg a többit sortrafó függ ic csere,tda8362e helyet volt itthon tda8362 3y.A gép beis indult kis sormeret meg szinkron hiányba.Amit találtam leirást kicseréltem de a szinkron hiba megmaradt.Erre a hibára is kell valamit cserélni vagy nem kompatibilis?Amit cserélte 8.2kohm helyett 47kohm 3.3kohm helyett 100kohm meg egy smd kondit 100nanora.Ha valaki tudja mit kell az még cserélni az segitsen elöre is köszönöm
Sziasztok!
A címben szereplő TV nem indul el. A 3,3V és a 12V tápok megvannak. A tápindító "SANDBY" vonal alapból 0V, néha 3,3V-ra felugrik. Az SDM service PAD leföldelése után az 53-as hibakódot villogja, ami a táblázat szerint a STBY processzor (elvileg) szoftveres hibájára utal. (Sok fórumon írták, hogy ez típushiba ennél az alaplapnál)
Elvileg USB-n lehet frissíteni a STBY szoftverét is. Ezzel kapcsolatban lenne néhány kérdésem:
- honnan lehet letölteni a megfelelő Stand-by firmwaret? (több helyen a STDBY_91.67.0.0 verziót említik, de sehonnan nem tudom letölteni)
- mennyire kényes az USB-PEN típusára/méretére stb. ?
- honnan tudom, hogy elindult-e/végzett-e a frissítéssel?
Service manual itt a Tanyán van róla. ("pfl8007"-re keresve a kereső feldobja).
Minden segítséget előre is köszönök!
Üdv:
Gyula