Service manuals, schematics, eproms for electrical technicians

PHILIPS CH GR2.4AA

TV - SERVICE MANUAL
Type: (PDF)
Size
2.1 MB
Page
30
Category
TV
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar philips manual?
Advertisements
Document preview [1st page]
PHILIPS CH GR2.4AA service manual (1st page)
Preview of PHILIPS CH GR2.4AA [1st page]
Click on the link for free download!
Document preview [2nd page]
PHILIPS CH GR2.4AA service manual (2nd page)
Preview of PHILIPS CH GR2.4AA [2nd page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
  • Also known:
    PHILIPS CH GR-2.-4AA GR2.4AA GR AA
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Philips 40PFL7007K/12 does not power on - Chassis QFU1.1E LA
Hi everybody, I have Philips 40PFL7007K/12 on repair. TV does not start up. I have checked the PSU and it seams to be OK. There seam to be problem on the main board. What I have tried… Well, there is +3V3-STANDBY coming from PSU to main board. This feeds up the main processor. This voltage has also been used to switch TV on. I have checked that switching signal from POWER ON button goes back to main board. But I did not check this whole path towards the processor as it is BGA package and it is covered by ceramic cooling plate. And here comes what is not clear to me. 1. How to check if the main processor works? Does it work on the +3V3-STANDBY when TV is is standby mode? 2. Can I somehow check if the PSU is working? May be by activating some pin? 3. I have noticed by measuring (ohm-meter) some capacitors on the main board (in circles on the picture) that there is very low resistance on them (4.5ohms). In the scheme it is shown that these capacitors are on the 1V5 (1.5V) line. Is this OK? Basically it does not give much current as I = 1V5 / 4R5 = 333mAmps. What do you think? Certainly there are low voltage data parts (RAM. Processor …) connected and such resistivity might be correct….?.... What I have also find that this 1V5 is split into 1V5M0 and 1V5M1. See the picture. I have removed the coils and measured resistance. Then 1V5M0 shows about 15ohms and 1V5M1 shows about 6,5ohms. The service manual is on this link: http://elektrotanya.com/philips_ch.qfu1.1e_la.pdf/download.html Thanks Martin
Philips 32pfl9603h Hálózatba dugva 10-ből 1x indul, de ilyenkor hibátlan MEGOLDVA!!
Sziasztok Valaki esetleg találkozott m ár olyan hibával, hogy egy 32pfl9603h-s TV ha bedugom a 220-ba, általában 2 -t villog végtelenítve, de ha nagy nehezen sikerül "jól bedugni", akkor hibátlan... Ha lekapcsolom távval standby-ba, visszakapcsol hibátlanul.. Csak az áramtalanítást nem tűri.. Laci
Philips 58PUS7855/12 TV-n nincs kep.
Sziasztok

Adott egy ilyen TV. 2 eves es par honapos. Ahogy lejart a garancia, szinte rogton meghibasodott. A tulaj csinalt egy hard-resetet (?!) es a TV ment tovabb... amig elo nem allt megint. Meg vagy ketszer elindult de most mar vegleg nincs kep.
En a kovetkezoket latom:
A TV indul, hattervilagitas van.
Kep nincs, egyenletes szurke a kep.
Hang mukodik, csatornat valt, stb.
Amikor hozta, ugy ertettem, hogy nincs hatter, LED-ekre gondoltam, de nem ez az eset.
Gyanakszom T-CON-ra, de az miert jonne helyre resettol? Amugy is mi lehet az a hard reset amit o elvegzett taviranyitobol?
Ha helyrejott, inkabb procira gyanakodnek... 
Meg sokat nem tudtam vele foglalkozni, de a T-CON megkapja a 12V-ot (11.96V) es a biztositekja sem szakadt.
Mast egyelore nem mertem
Van esetleg otletetek, hol kezdjem?
Csatolok par fotot a TV-rol, barmilyen mas infot szivesen megadok.

Minden jot,
Janos
Philips 2.25AA Hiba
Sziasztok! Volna egy Philips MD2.25AA chassival szerelt dög ami egy idő után leáll és folyamatosan villog a standby led-je. Ez a leállás megközelítőleg 2-10 perc között jön elő. Egyenlőre még nem méregettem rajta mert a hátlap levétele után megállt a ketyegőm úgy tele van zsúfolva szegényke :hmmm: Ha valaki futott már bele ilyen hibába ezzel a döggel kapcsolatban azt szívesen meghallgatnám :D Mert nem akarok beleverni órákat mire szétszedem, plusz napokat mire megtalálom a hiba okát és még az e biztos hogy gazdaságos a javítása mert figyel a jobb oldalon egy rakás digi lap :S Ja annyit látok hogy a tápját kikondizták előttem mert szép új elkók virítanak benne :) Előre is köszönöm a segítséget mindenkinek :)
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce