Service manuals, schematics, eproms for electrical technicians

PHILIPS FTV1 9

TV - SERVICE MANUAL
Type: (PDF)
Size
1.8 MB
Page
15
Category
TV
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar philips manual?
Advertisements
Document preview [1st page]
PHILIPS FTV1 9 service manual (1st page)
Preview of PHILIPS FTV1 9 [1st page]
Click on the link for free download!
Document preview [2nd page]
PHILIPS FTV1 9 service manual (2nd page)
Preview of PHILIPS FTV1 9 [2nd page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
  • Also known:
    PHILIPS FTV-1 FTV1 FTV
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Philips 32pfk6509/12 magától be kapcsol, nem lehet ki kapcsolni

Üdv mindenki 

egy kis segítségre lenne szükségem a címben említett tv-vel kapcsolatban.

Áram alá helyezve magától be kapcsol, ki kapcsolni nem lehet se a készülék gombjaival se távval.ezen kivül a menübe se lép be .

Olyan mintha hotel mode-ban lenne vagy van is.

van e valami megoldás

sasszi:    tpm14.2e

Üdv Imre

Philips 37PFL3312/10 LCD tv tápegység elsőre nem indul, csak kb 10-15. bekapcsolásra
Sziasztok, Adott egy Philips 37PFL3312/10 LCD TV. A probléma a következő: bekapcsoláskor világít a piros led. (Standby). 1. Indítás átvált a piros led kékre 2-3 mp utána visszavált pirosra. Az összes elkót cseréltem. Problémát nem oldotta meg. Tápegység típusa: DPS-168BP kb 10.-15. bekapcsolásra elindul azután napokon keresztül működik. Segítséget előre is köszönöm! üdv: Csady
Philips 40PFL7007K/12 does not power on - Chassis QFU1.1E LA
Hi everybody, I have Philips 40PFL7007K/12 on repair. TV does not start up. I have checked the PSU and it seams to be OK. There seam to be problem on the main board. What I have tried… Well, there is +3V3-STANDBY coming from PSU to main board. This feeds up the main processor. This voltage has also been used to switch TV on. I have checked that switching signal from POWER ON button goes back to main board. But I did not check this whole path towards the processor as it is BGA package and it is covered by ceramic cooling plate. And here comes what is not clear to me. 1. How to check if the main processor works? Does it work on the +3V3-STANDBY when TV is is standby mode? 2. Can I somehow check if the PSU is working? May be by activating some pin? 3. I have noticed by measuring (ohm-meter) some capacitors on the main board (in circles on the picture) that there is very low resistance on them (4.5ohms). In the scheme it is shown that these capacitors are on the 1V5 (1.5V) line. Is this OK? Basically it does not give much current as I = 1V5 / 4R5 = 333mAmps. What do you think? Certainly there are low voltage data parts (RAM. Processor …) connected and such resistivity might be correct….?.... What I have also find that this 1V5 is split into 1V5M0 and 1V5M1. See the picture. I have removed the coils and measured resistance. Then 1V5M0 shows about 15ohms and 1V5M1 shows about 6,5ohms. The service manual is on this link: http://elektrotanya.com/philips_ch.qfu1.1e_la.pdf/download.html Thanks Martin
Philips 24PFL3108H/12 (ch:TPN10.1ELA) logó előjön, leáll, újraindul. Megoldva !
Sziasztok ! A fent emlitett laposnak valószinü hogy boot hibája lehet. Bekapcs. után megjelenik a Philips felirat és el is tűnik de a háttér világítás megmarad később az is kialszik, újragyúl de nem egyidőbe a kijelzővel majd később újra megjelenik a felirat ,és ez igy ismétlődik ,távirányítóra nem reagál ,board gombok nincsenek,board led nem világit. A mainbord 715G6092-Mod-000-004N . Esetleg flash csere segít-e, egyéb egyszerübb megoldás is szóba jöhet ? Előre is köszi a segitséget: Pali
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce