Service manuals, schematics, eproms for electrical technicians

PHILIPS HI529

HOUSEHOLD - SERVICE MANUAL
Type: (PDF)
Size
2.0 MB
Page
5
Category
HOUSEHOLD
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar philips manual?
Advertisements
Document preview [1st page]
PHILIPS HI529 service manual (1st page)
Preview of PHILIPS HI529 [1st page]
Click on the link for free download!
Document preview [2nd page]
PHILIPS HI529 service manual (2nd page)
Preview of PHILIPS HI529 [2nd page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
  • Also known:
    PHILIPS HI-529 HI529 HI 529
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant HOUSEHOLD forum topics:
Philips Saeco GranBaristo nem kapcsol be készenlét ok resetelni kellene megoldva
Sziasztok ezen a gépen csak készenlét van nem hajlandó bekapcsolni érintő kijelző jó szervizbe betudok lépni bluetottal rá tudok csatlakozni de nem kapcsol be a pover gombra lehet hogy gyerekzaron van?hogyan lehetne resetelni hogy gyárirol induljon.
Philips gőzállomások hibajelzéseit keresem
Sziasztok
Munkahelyemen több ilyen gözölős vasaló van. Van amelyik gőzgenerátoros és van amelyik a talp melegét használja a gőz gyártáshoz.
Philips perfectCare Aqua
Philips perfectCare Pure
A hiba, hogy villognak és a használati utasításukban erről semmi szó nem esik. Nem a vízkőmentesítő jelez. Az egyiknél a nyél villog szaporán a másiknál a bekapcsoló és az eco felváltva.
Szétszedve nem találtam hibás alkatrészt. (biztik, talp, szeleptekercs, fűtőszál, )
Segítségeteket kérem ki találkozott már ezzel a hibával?
Köszönettel Laci
Philips ADG-817 Mosogatógép aszinkron motor bekötése
A segítségeteket szeretném kérni a fent nevezet mosogatógép aszinkron motorját szeretném ki próbálni direktbe rá kötni egyfázisú hálózatra,ha tudtok kapcsolási rajzot küldeni.A motor ohmikus kivezetései három vezetékből áll kék ,fekete,barna.A fekete-kék(30ohm)kék-barna(40ohm)fekete-barna(20ohm)és van egy gerjesztő kondi ami 400V 12uf.Azt szeretném kérdezni,hogy melyik vezetéket hová kössem,hogy tudjam működtetni az egyfázisú hálózatról.Előre is köszönöm a segítséget.
Philips HP5847 shaver stopped working
Hope I've selected the right forum, I don't speak Hungarian! I have a Philips shaver HP5847 in which I was replacing the rechargeable battery. Unfortunately while trying to fit it (with long tags attached) something must have shorted out while I was turning the shaver around and it suddenly stopped working (the motor had initially immediately started running as I inserted the pre-charged battery pack). I found the Service Manual on this site but unfortunately there are no component values shown on the schematic. It was helpful to see the circuit diagram and I noted a (small-value) resistor R20 in series with the motor (for load current-sensing). I found no conductivity through it, so I shorted that out and miraculously the motor started working! I checked out the data sheet for the SAA1500T charge controller but other than confirming my understanding of the function of the resistor gave no help in working out what kind of value I should replace it with... I guess it's a function of the actual motor parameters. I imagine it is going to be of the order of 1 Ohm or less but this type of surface mount resistor does not appear to have a value marking on it unlike the other components on the PCB. Can anyone suggest a value for R20 please?
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce