Üdv. T. Kollégák!
Tárgybeli tv sorvégtranzisztor zárlatos volt. Különösebb okot nem találtam, hogy mitől keletkezett a hiba, de azért átforrasztottam az ilyenkor szokásos részt (pl. eltérítő stecker..) és beforrasztottam egy új tranzisztort. Kép hang ok, de a raszter jobbról balra el van tolódva, a jobb oldal domború, a bal oldal homorú, mint amikor a BOW koppanásig van állítva. Sortranzisztor igen melegszik.Szerviz menűben az E/W korrekció működik, H-shift is, ami mechanikus három állású kapcsoló. Egyedül a sorfázis nem szabályoz semmit, ami független az ew-től. A F-box megkapja a H-flyback impulzust, impulzuskondikat ellenőriztem illetve cseréltem a kritikusabb helyeken. Tápok jók, nincs brumm. Ha leválasztom az EW-t, akkor pillanatokon belül összemegy a kép (sorméret), majd tilt a gép. D410 cserélve, változás semmi. Néhány évvel ezelőtt volt ilyen hibás gép nálam és azt sikerült megjavítani, de nem emlékszem vissza, hogy mi volt a hiba oka. Arra emlékszem, hogy nem a CXA2165Q volt rossz. Tudnátok segíteni?
Köszönettel,
elbandi
Hi, my SAMSUNG UE40D5000 tv doesn' t work anymore. The red led light indicating that the tv is plugged is not powered when I plug in the tv. The original power board modem is BN44-00473B. I have checked the voltage on the connector to the mother board of the tv, and it was 0 instead of 5.3V or 13V on the different pins, with the fuse still working and no obvious overheated part on the power board and no bulging capacitor seen neither.
I have then changed the power board with a used one bought on ebay, which model BN44-00473A is said to be compatible. It has then worked perfectly 2 days until yesterday. This morning I had to move a little bit the tv, what I did very gently, and got really disappointed as I plugged it and didn't see the red led light on anymore.
Since this morning, the power board seems to be broken once more ( I have moved from my original flat 1 week ago and don't have a multimeter to check once more that the fuse is ok and what are the voltage on the connector to the mother board )
I am wondering if this new power board failure is just bad luck, 2 days after receiving this other power board circuit ( that is a used unit, not brand new) or if the mother board could have damaged it. In the first case I would send the power board back to the seller, otherwise I will probably give up as I don't have time and skills to repair the tv.
My question is : do you think the mother board or another unit connected to it, can damage the power board ?
Thanks for your help and answers !
Sziasztok!
Az alábbi linken látható hibát produkálja a TV:
https://yadi.sk/i/EEZOibRZkJ6UZ
A hiba nem mindig jelentkezik, illetve eltérő időközönként jön elő.
Elkezd vízszintesen "zizegni" a kép, majd egyre jobban szétcsúszik, a vége fele a kijelző is ki-be kapcsolgat. Ha lekapcsolom, és áramtalanítom egy időre, akkor megint jó lesz(kihűl vagy kisül?).
A kondikat átnéztem, sehol sincs púpos, vagy aminek kifordult volna az alja.
Viszont valaki már járt a tv-ben, mert a Q8333( 2SK2698 )FET-et már cserélték.
Plazma tvben nem vagyok otthon, így azt sem tudom, merre van előre..
Köszönettel : -=L=-
Sziasztok!
Letört a tunerről a koax vég.Vissza forrasztottam.A problémám hogy a test és a meleg pontja között rövidzár van.
Töltöttem le innen rajzot de nincs benne részletes kacsolási rajz.Hány ohmot kellene mérnem ott?
Elvileg 75 ohmos a csatolás.
Köszönöm!
Csiszár Csaba