Service manuals, schematics, eproms for electrical technicians
SONY FE2 TIPUSHIBAK INF
TV - INFO-TIPS
Type: (PDF)
Size
25.2 KB
Page
1
Category
TV
INFO-TIPS
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for other manual?
Document preview
SONY FE2 TIPUSHIBAK INF service manual (1st page)
Preview of SONY FE2 TIPUSHIBAK INF [1st page]
Click on the link for free download!
Please tick the box below to get download link:
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • Please take a look at the below related repair forum topics. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!


Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
SONY KV-29X1D
SONY KV-29X1D (részletes)rajzra lenne szükségem sürgösen!Tünik el a kép,hang van.Ilyenkor a képernyő elsötétül és néhany masodperc mulva helyrejön.....majd ismételten ez történik.
Sony KV21X4B
Szevasztok! A tápegység volt rossz,a Q 601 és a D 603 átment vezetőbe.Csere ,valamint az elkók cseréje után beindult,csak nem tárolta a programokat.Írtam egy a Fülesmestertől kapott tartalommal egy eepromot.Léptette a csatornákat a tasztról,mert a távot nem érzékelte.Az infravevő csatlakozója az alaplapon forrhibás volt,mostmár hallgat a távra,csak nem indul.A led villog,majd a 7-es hibakód jelenik meg. Lehet ,hogy a vezérproci ? A buszokat lekötöttem a tunerról,audio prociról és a videovezérlőről is, de nem változik semmi. Ferenc.
-SOLVED- SONY KDL-32EX600 red led 2 flashing - negative 120V backlight missing PSU GE3D APS-272
Hello
I have on my table this sony kdl32ex600 with backlight issue. It's a common failure of this psu but i do not find any part faulted on this board.
The schematic it is almost the same, with minor differences with GE3B found at page 56 on this service manual:
https://elektrotanya.com/sony_kdl-32ex600_kdl-40ex600_kdl46ex600_chassis_az1-k.pdf/download.html
Uploaded only the page 56 from this sm to easing the search.
The red led it's flashing 2 times, meaning psu faulty. Indeed the led backlight does not light.
With the PSU outside of the tv, just with one resistance of 180ohm between standby ( pin 1 3,3V on connector CN6150 ) i get this values
on in:
starting with pin 1

1  +3,3V ST-BY
2  +3,3V AC_OFF_DET
3  +3,3V POWER_ON (with resistance 180ohm between pin1 and pin 3)
4  +12,56V AUDIO_12V
5  0V AUDIO_12V_GND
6  0V REG_12V_GND
7  0V REG_12V_GND
8  +12,6V REG_12V
9  +12,6V REG_12V
10  +0,1V BL_ERR
11  +3,3V BL_ON
12  0V DIMMER
13  0V DIMMER_DC
14  0V T-CON_Vcc_12V
15  0V T-CON_ON
All measure done at secondary ground point C6800 GND as reference.
Meanwhile, the led connected to CN6800 will remain with no light at all. The CN6800 will deliver positive 91V.
The negative branch will deliver at CN6801 ( both pin1 & 2 ) just -1V.
In the training manual found always in here at
https://elektrotanya.com/sony_kdl-32ex600_40ex600_46ex600_chassis_az1k_training%20manual.pdf/download.html
at page 56 will say "SHORT" at pin 12 DIMMER for testing the PSU, always with pin 3 POWER_ON connected to 3,3V ST-BY - pin1.
If i'll put a 180ohm resistance between GND and pin 12 DIMMER, then the tension on CN6800 will rise to +179V and the negative from the CN6801 will rise to -5V, the backlight led will light very very weak.
All tension from CN6805 will remain the same, except the BL_ERR will rise from +0,1V to +1,1V.
With only power_on pin 3 shorted by 180ohm resistance to the pin 1, i get this weak oscillation at emiter of Q6816 + Q6817

[URL=https://picturepush.com/public/16067400][IMG]https://www1.picturepush.com/photo/a/16067400/640/diverse/Q6816Q6817.jpg[/IMG][/URL]

With pin 12 DIMMER shorted ( always by a 180ohm resistance ) at GND, the oscillation will change from 250khz 1,6vpp to almost 70khz at 0,81Vpp. as below:

[URL=https://picturepush.com/public/16067401][IMG]https://www1.picturepush.com/photo/a/16067401/640/diverse/20181117-175255.jpg[/IMG][/URL]

Already checked the capacitors C6828 / C6830 together with D6805 / D6806.
Also checked the L6800 ( trafo ) and i've get 5,5mH instead of 5mH, i think it's ok.
All fuse checked, ok.
Q6814 and Q6801 tested under mosfet tester, ok.

[url=https://picturepush.com/public/16067402][img=https://www1.picturepush.com/photo/a/16067402/220/16067402.jpg][/url]

IC6800 & IC6801 gave +9V and respectively +2,49V

Already checked various components all over the board, i am out of ideas.

Any idea or help would be apreciated.
 
KDL-50W755C Sony TV 1 TB-os USB winchesterről nem jelennek meg az MKV fájlok és a mappák
T.Mindenki! KDL-50W755C Sony TV 1 TB-os USB winchesterről nem jelennek meg az MKV fájlok és a mappák. A használati utmutató szerinti Usb-be van csatlakoztatva. Nem felvenni szeretnék, hanem lejátszani. A távirányitó idönként nem müködik, csak a tv hálózati dugójának kihúzása és visszadugása után müködik. Nincs hálózati kapcsolója. Ezek hibák vagy nem? Mi a megoldásuk? Köszönettel gombocda55
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Recycling