Service manuals, schematics, eproms for electrical technicians

THOMSON-TX92SD7061-24C04-

TV - EPROM
Type: (HEX)
Size
1.4 KB
Page
---
Category
TV
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar thomson manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Download free of charge (10 files / day):
Download is being processed. Please wait...
Download processing...
  • Also known:
    THOMSONTX 92 SD 706124 04 THOMSON TX92SD7061 24C04
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
THOMSON 28DG170G TV SORVÉG HIBA
Sziasztok! Thomson tv sorvég tranzisztor rossz és a colectorán van egy kondi A/ R76 MKP 0146 2000 van ráírva az oldalára a tetején 3.5 nem találok róla infót 14nf vagy 3.5nf. Ha tudtok egy pontos értéket írjátok már meg előre is köszi. Csaba
Thomson tx91chassis nem indul Megoldva
Szevasztok Lenne itt egy ilyen tv ami bekapcs után egy pillanatra indul,hallani de le is áll.Tápok jók,ellenben a függőleges ic TDA1771 es pin tizese rövid a testel,érdekes módon volt hogy beindult egy viz szintes csikkal ,namost kivettem az ic t de a sor igy sem indul csak egy tized másodprcre,tilthat e a proceszor a függőleges nélkül,rajzom az nem egészen ehez van de hasonló hozzá.
THOMSON 29DM182 nem hangol
Üdv mindenkinek! Van egy thomson 29dm182 TV, sasszi ITc008. Az alap hiba az volt, hogy a tulaj működés közben nekilökte a falnak a TV-t, és tönkre vágta a tunert. Tuner csere után nem lehet hangolni. A tuner pontjain a feszültségek rendben a buszokon szkóppal aktivitás látható. Kicseréltem az epromot, beleírtam a gyári adatokat. Megkezdem a hangolást és a következő történik: Elindul a frekvencia számlálás, látható a képernyőn, de nem változik a kép tartalom. Amint végez, csak egy program marad, ami az elején is megvolt. Úgy tűnik, hogy minden egyéb dolog rendesen működik. Van-e. valami ötlete valakinek? Köszönettel: Myckie
LEDTV Thomson 32HU5253W táphiba
Sziasztok!
Valakinél már volt javításon, de nem tudta megjavítani..
Stby tápja jó (3,3V) ez azonnal adja a PW-ON jelet (3,3V) de nem indul be a fő táp (24V).
Külön 24V tápegységemmet ráraktam akkor működik a TV, így mainboard hibát kizártam.
Az előző "szervízes" cserélte szekunder oldalon Q204 (npn), meg lehet hogy kivette primerbe R234 (10k) ami a Q101 lábaira megy.
Amiket én cseréltem:
primerben Q101 szétpukkanva (smd mosfet 2N7002),   R234 (rajz szerint kell bele).
szekunder oldalon Q202 (npn) zárlatos,  Q203 (pnp) zárlatos.
Vettem már új IC-t is U101 (FAN6754), raktam TL431(U102) -et is TO-92 est smd helyére.

24V helyén megjelenik egy pillanatra 3,6V a TL431(U102) kiad 2,5V-ot , optokopler (PC1) szekunder oldalán 1.2V lesz, de a primer oldalon mindkét lábán 0V marad (pin3, pin4).
Primeren a FAN6754 FB lábán (pin2) 0,2V van és kb 2-5V kellene hogy legyen, ez szerintem azért nem tórténik meg mert a Q101 (smd 702) mosfet GND-re behuzva van, mert a a PC3 optokopler vezetésbe lép de vezetnie is kell, nem értem hogyan működhet ez egyáltalán..
FAN 6754 lábain mérve:
tápja pin7 19V jó,
pin4 HV 84V  szerintem ez is jó.,
pin5 oscilátor 0,7-1V jó

Táp panel jele: 40-P081C0-PWD1XG
Hogyan tudnák FB lábra 2-5V-ot teremteni?

Táprajz a rendezetlenek közt jelenleg..
https://elektrotanya.com/thomson_32hu5253w_40-p081c0-pwd1xg_40-p061c2-pwb1xg.pdf/download.html
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce