Service manuals, schematics, eproms for electrical technicians

29V50

TV - EPROM
Type: (DAT)
Size
256.0byte
Page
---
Category
TV
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar 29 manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Download free of charge (10 files / day):
Download is being processed. Please wait...
Download processing...
  • Also known:
    29V-50 29V50 29 50
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Schneider screenland 23M901
Sziasztok! A fenti típusú LCD TV/Monitor készülékkel adódott az a hibajelenség, hogy készenlétből be tudom kapcsolni, a készülék kijelzőjén megjelenik egy bootolási csík. Amíg működött az éledési folyamat végén megjelent a kép, most sajnos lekapcsol a háttérvilágítás és készenlétbe áll vissza. Az éledési folyamat végén, amíg nem kapcsol le a háttérvilágítás a távirányítóval pl a bemenetválasztó menü is feljön. Tápfeszültségek rendben vannak, megvilágító cső hibájára gyanakszom, de sajnos ilyen hosszú próbacsővel nem rendelkezem. Hogyan tudnék megbizonyosodni a csőhibáról? Minden segítséget előre is megköszönök! Bagoly69
Orion T32-DLED-S 17IPS11-17MB95M nincs készenlét (Megoldva)
Szia!

Megtaláltak ezzel a csodával. 
Az elmondás szerint rég nem használták, és a hálózatra csatlakozás után  nem indult el.

Készenléti led sem világít.
A tápot átmérve a 68uF 400V kondenzátor csak 38uf volt mérésre. A mért feszültség 250V.
Csere után 320V lett állandó.
A fet és a többi alkatrész átmérve, kiforrasztott állapotban, jónak tűnnek mérve.
A táp üresben, és az alaplap, háttért rel ugyanazt produkálja, mindenhol a sec körben 24V mérhető, de pulzálással, leesik 15-17-re, majd vissza 24-re.

A készenléti 5V nincs jelen, Az alaplapon a stab kockán nem jelenik meg semmilyen feszültség, a bedugott pendrive kb. másodpercenként kap 5V-ot.

Nem találtam hozzá beleírható tartalmat.

------------------------
A készülék ismét üzemképes.

A  68uf/400V kondenzátor  csere 82uf/450V.
A  Q106 FDC642P Source-Drain zárlat miatt cserélve.

/A Fet levétele után, az S106 pozició átkötésével a készülék üzemelt./

Külön köszönet Shizo és Gabor2 tagtársaknak a segítségért!


 
LG 55UH605V TV készülék képernyő egy harmada sötét

Tisztelt Fórumtársak !

Segítségeteket szeretném kérni a fent nevezett LG TV készülék hibájának a felderítésében .

A készüléket szemből nézve a képernyő jobb oldalának egy harmada sötét .

Samsung CS-29M17MH chassis s16a loses picture
:help: Hi,this set will play tv or AV normal for few minutes and the video will disappear ,while the heaters are on and the eht normal and sound ok.all voltages are normal.I changed all eletrolitics caps on the B+ ,190v,12v,5v and 3v rails.This is an old set.now i suspect the x ray protection circuits ,but all seems well.But when no signal applied no aerial input the set dont loose video till it goes to standbye,telling that when much current is drawn (video or lopty current)is then that the fault happens.
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce