Service manuals, schematics, eproms for electrical technicians

INGELEN COL39GW2 TUBES RADIO SCH

AUDIO - SERVICE MANUAL
Type: (JPG)
Size
316.9 KB
Page
---
Category
AUDIO
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar ingelen manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Download free of charge (10 files / day):
Download is being processed. Please wait...
Download processing...
  • Also known:
    INGELEN COL-39GW-2 RADIO COL39GW2 TUBES COL 39 GW
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant AUDIO forum topics:
Hővezető paszta
Szép reggelt mindenkinek! Az egyik munkám során több száz CATV végfok IC-t kell beszerelnem és mérnem. A hőelvezetéssel kapcsolatban lenne két kérdésem: 1. Én régebben hangfrekvenciás végfokok esetében és CATV végfok IC-k esetében is sima szilikonzsírt használtam az IC és a hűtőborda közé. Most előírt a hővezető paszta használata. Mennyivel jobb ez az anyag a szilikonzsírnál? Az biztos, hogy lényegesen többe kerül. 2. 600 db IC esetén kb. mennyi hővezető paszta szükséges? Van valakinek ezzel kapcsolatos tapasztalata? A CATV végfok IC képét mellékeltem. Nem pontosan ez az IC lesz, de a méret azonos. Üdv.: Kumi
SAMSUNG MAX-S720 3CD-s hifitorony - nem jó forgat
Sziasztok! Ez a 3CD-s torony a tányért néha nem a CD "lukra" rakja hanem felibe és beszorul a tányér. Valamikor 10x is forgatgatom jó helyre áll be . Rosszak voltak a nyomogombok azokat kicseréltem. A tányérfogatás csigás, NEM gumiszijjas, így a megcsuszást kizárom. Opto-kaput alkohollal megmostam már. A tányéron az opto rések megvannak. Lift gumiszijjas, de az jól müködik. Lézer olvas. Amikor kint van a tányér , már ott is félre tudja állítani pl "CD CHANGE" gombbal, motort is megfujtam már WD spay-el, nem erôlködik. Amikor behuzza a tányért valamikor 2 teljes kört is forgat, de nem mindig. Amikor "felesre" állitja magát, akkor a motor általában lelassul máshogyan is zug.. Ilyenkor megnyomom az EJECT-et kinyilik a tányér és következô becsukásnál már lehet hogy jó is lesz. Volt valakinek ehhez hasonló hibája?
ONKYO TX-SR307 nincs hang
Sziasztok,

Onkyo TX SR307-es HDMI-s erősítőnek nincs hangja. Bekapcsol, minden funkció működik rajta de nem jön ki rajta hang.

A HDMI-DSP panelen néztem az IC-ket, egyik sem BGA tokozású, mind SMD. Gondoltam, ezek nem forrasztották ki magukat mint a BGA-s társaik.

Kicseréltem ezen a panelen az SMD elkókat, a helyzet nem változott. 

Érdemes újra forrasztanom az SMD DSP ic-t?

Valakinek hasonló helyzet?

(egy érdekesség: ha a B hangfal kimenetre kötök hangfalat és a hangerőt max-ra teszem halkan ugyan de jön ki hang az erősítőből)
Sony STR DH130 protection mode
Friends Sony STR DH130 goes into protection mode soon after turning on.  It works for a second then can hear loud pops from speakers.
I've tried the suggested methods to fix but nothing works.  Correct impedance speakers.  Speakers wired correct.  Good ventilation.
I've tested the output transistors in circuit and I don't see anything unusual.  I may pull them to test but will wait for advice here.  I also measure
about 57 volts on the emitter resistors.  Seems high to me.  Anyone?
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce