Service manuals, schematics, eproms for electrical technicians

PANASONIC 25L10R

TV - EPROM
Type: (RAR)
Size
875.0byte
Page
---
Category
TV
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar panasonic manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Please tick the box below to get download link:
  • Also known:
    PANASONIC 25L10R 25 10
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Panasonic TX-29 PM1P (CP-521F/FS) Nem indul, készenlét sincs.
Üdv! Tisztelt mesterek! Fent nevezett készülék hiba behatárolásához szeretnék segítséget kérni. A TV utóljára a főkapcsolóval ki lett kapcsolva, azóta bekapcsolási kísérletnél a LED egyet pirosan villan, a relé kattan és kikapcsol. Nem vagyok TV szerelő, de ezt a készüléket szeretném beindítani úgy hogy minél kevesebb alkatrészt vegyek bele fölöslegesen. Odáig jutottam, hogy a tápban az összes elkó ESR-re ellenőrizve- cserélve, a diódák digitműszerrel mérve jónak tünnek, panel átforrasztva, zárlatot sehol nem találok. A tápot az R803- nál leválasztva és a C813-on 60W-os izzóval terhelve az izzón megjelenik 141 Volt bekapcsolástól kb 8 másodpercig. Ezalatt minden előírt feszültség megvan a sabok kinenetén, valamint a Q813-Q814 és Q815-Q816- on is megvan a 2x 1V8, valamint az I822 4-es lábán lévő DECDIG bemeneten 2.5V mérhető ezalatt a LED sötét. A kb 8 másodperc letelte után kikapcsol és a LED folyamatos villogásba kezd. Innentől az izzón marad 53Volt, valmint megmarad a Q815-Q816 közös pontján lévő 1.8Volt. (+V8_1). A többi fesz. eltünik. És itt akadtam el. Pityesznek és Fülesmesternek az eddigiekben nyújtott email-os ill. telefonos segítségét ezúton is köszönöm. Üdv.nagybarna
Panasonic TX-21S4TP Ch.:Z7
Sziasztok! Hozzám került a fent nevezett készülék. A tulaj annyit mondott hogy nem jó, szétkaptam, a vert. IC körül elég sok kh volt. Átforrasztottam és cseréltem egy pár elkót, a készüléket bekapcsolva egy pillanatra mintha indulna (jellegzetes hangok) megjelennek a tápfeszek de abban a pillanatban le is kapcsol és a készenléti LED folyamatosan villog. Volna valakinek ötlete merre keressem a hibát? Zárlatot még nem találtam. Köszönöm a válaszokat.
Broken Panasonic TX-42ASN658
I got a broken Panasonic that will not start. It does show the red front LED and the power supply delivers 5,3Volt standby. Only when you try to start by remote or push button on the set it will only flash the red LED and does nothing more.

After a while, the red LED will start to flash repeatedly 13 times.

Since the 5,3 Volt standby run straight to the main board I wanted to check there but no luck finding the schematics.

Any insights?

After several attempts the TV finally started and I could enter the menu screen. Normal functionality. But after switch off it takes again several attempts. What is going on ?
Panasonic TX-42P2E (ch: GPH13DE) plasm 13-at villog, nem kapcsol be
Üdv!
A címben említett plasma a fenti hibajelenséget produkálja. A meglévő SM csak 12-es kódot ír, igy nem igazán tudom az okát. Mérve, már amit lehet minden ok. Y-sus, Z-sus probára cserélve, helyzet ugyan az.
atti1
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce