Service manuals, schematics, eproms for electrical technicians
Type: 
(PDF)
(PDF)Size
5.0 MB
5.0 MB
Page
22
22
Category
TV
INFO-TIPS
TV
INFO-TIPS
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for other manual?
Good luck to the repair!
Please do not offer the downloaded file for sell only use it for personal usage!
Looking for other manual?
Document preview
Click on the link for free download!
Document preview
Click on the link for free download!
Please tick the box below to get download link:
- If you have any question about repairing write your question to the Message board. For this no need registration.
- Please take a look at the below related repair forum topics. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition,
some files are archived,If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Sziasztok!
Tudom, hogy volt már téma, találtam is Loewe készülékbe, de a Panasonic készülékhez nem találom a megoldást! Olyant találtam, hogy nem sikerült.
A benne lévő TDA8175-ös IC-vel van függ. eltérítés, csak a felső harmadában elég sűrűn visszafutási csíkos. A tulaj szerint egy idő múlva össze is megy a kép. A 220uF-os kondit kicseréltem. Rövid idő után már elég meleg az IC.
Mit csináljak? Mit javasoltok? Feltételezem, hogy a benne lévő IC hibás.
Köszi.
Üdv: formasu
Sziasztok
A fenti tipusú tvhez(euro4h sasszi) keresek digitális vezérlő panelt
honnan lehetne beszerezni?
köszi Miki
Manufacturer: Panasonic
Type: TX-L42ETW5
Chassi: LA35
Hello everybody,
I could determine or measure the following with the device:
Device does not start anymore, stand-by LED lights red when device is plugged in and flashes red as soon as an IR command (key press) is sent via the remote control. Voltages of power supply STB 5V and signal LCD_TV_SUB_ON come from A-board. Power supply starts, supplies P15V and SUB1.1V, 1.5V, 1.8V, 3.3V, 5V, HDMI3.3V and USB5V are generated on the A-Board (stand for about 2.5 seconds). Then signal LCD_TV_SUB_ON goes low (voltages go away to STB 5V) and after about 2 seconds back to high (endless). What is missing is the voltage PNL12V which is switched on by PANEL_VCC_ON2. PANEL_VCC_ON2 always has a low signal and does not change its state. Power supply also provides for the 2.5 seconds the 24V for the backlight. Clocking of LCD_TV_SUB_ON starts immediately after plugging in the mains plug (also without IR command). SOS error code is not output. The over-voltage circuit in IC 5000 pin 7 also does not respond. Attached is the timing diagram from the technical training of Panasonic where I have drawn until when the boot process behaves normally.
In my opinion a mistake on the A-board? Does anyone have a tip?
greetings
Andi
Type: TX-L42ETW5
Chassi: LA35
Hello everybody,
I could determine or measure the following with the device:
Device does not start anymore, stand-by LED lights red when device is plugged in and flashes red as soon as an IR command (key press) is sent via the remote control. Voltages of power supply STB 5V and signal LCD_TV_SUB_ON come from A-board. Power supply starts, supplies P15V and SUB1.1V, 1.5V, 1.8V, 3.3V, 5V, HDMI3.3V and USB5V are generated on the A-Board (stand for about 2.5 seconds). Then signal LCD_TV_SUB_ON goes low (voltages go away to STB 5V) and after about 2 seconds back to high (endless). What is missing is the voltage PNL12V which is switched on by PANEL_VCC_ON2. PANEL_VCC_ON2 always has a low signal and does not change its state. Power supply also provides for the 2.5 seconds the 24V for the backlight. Clocking of LCD_TV_SUB_ON starts immediately after plugging in the mains plug (also without IR command). SOS error code is not output. The over-voltage circuit in IC 5000 pin 7 also does not respond. Attached is the timing diagram from the technical training of Panasonic where I have drawn until when the boot process behaves normally.
In my opinion a mistake on the A-board? Does anyone have a tip?
greetings
Andi
sziasztok
Panasonic TX-W32D4F (euro 5L sasszé) hiba jelzése folyamatos 2 villogás, pillanatra van nagyfesz , de letilt és villogja a 2 -ket.
kérdezném a pana hibajelzéseket hol találnám, vagy aki tud légyszi segítsen.
Attila
Similar manuals:
PANASONIC TC-32LX80LB TC-37LX80LB SERVICE INFO
PANASONIC TC-32 26LX600 TC-23LX60 LCD TV TRAINING
PANASONIC TC-L37U22X CHASSIS LA03 INFO
PANASONIC TC-L42D2 TC-L37D2 TC-L42U25 TC-L37U22 TC-L32U22 TC-L37X2 TC-L32X2 TC-L37C22 TC-L32C22 LCD TV TECHNICAL GUIDE 2010
PANASONIC TC-L42D30 TC-L37DT30 TC-L32DT30 TC-L42E30 TC-L42E3 TC-L37E3 TC-L32E3 TC-L19C30 LCD TV TECHNICAL GUIDE 2011
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!
E-Waste Recycling