I got a broken Panasonic that will not start. It does show the red front LED and the power supply delivers 5,3Volt standby. Only when you try to start by remote or push button on the set it will only flash the red LED and does nothing more.
After a while, the red LED will start to flash repeatedly 13 times.
Since the 5,3 Volt standby run straight to the main board I wanted to check there but no luck finding the schematics.
Any insights?
After several attempts the TV finally started and I could enter the menu screen. Normal functionality. But after switch off it takes again several attempts. What is going on ?
Hi!A hiba kb 3-4 óra elteltével kikapcsol majd 4 et utána 10et villog,valamikor csak 10et. Néztem az sm en táp hiba.Át elkóztam volt egy pár rossz esr re is kimértem kh is volt,de a hiba még mindig úgyanaz.Tápfeszek rendbe melegitésre nem változik semmi.Üdv
Hi
I am having trouble finding any information regarding this product.
The unit powers up and the output is displayed on the screen for between 0 and ten seconds, the unit then powers down, the red standby LED on the front of the unit blinks then remains off for 5 seconds then blinks again.
This cycle continues until the power is disconnected, if the power is reconnected the unit goes back in to stand by (red led steady) it will then power on again.
Also in the error mode (red led blinking) and the power button on the back of the unit is pressed twice it will power up but this does not happen if the remote is used.
I have tested various capacitors and diodes but all seems well, I have also replaced the power supply with a reconditioned unit but this has not helped.
I have been unable to obtain any service information for this product.
So any input would be most helpful.
Thank you
Stephen Fry
Sziasztok!
Megint itt maradt nálam egy készülék,a tulaj nem akart rá költeni.A nagyfesz trafója füstölt le. Az új postával 7-9e forint .Hát költeni én se nagyon akarok rá de gondoltam kísérletezem vele kicsit,időm van.Nem egy rossz tévé,síkképcsöves 110 fokos,68cm-eres rendszer fesz:142V. Találtam itthon egy 90 fokos 51cm!!!-eres tévéhez való samsung trafót ami 125 Volttal működött. Gondoltam megnézem vele hogy kiderüljön van e más baja is a cuccnak arra megteszi.Szabályzó hurkot felvágtam és tápfeszt beállítottam egy potival 125V-ra(átlag fényerőnél).Szerencsére a TV alapból úgy készül hogy van a hálózati trafójának egy 123V-os kimenete is így arról hajtottam a trafót,persze a hurokbontásra így is szükség van. A samu trafó 24 voltos kimenetét pár menettel a vason felhoztam a szükséges 37.5 voltra,a többi kivezetés nagyjából passzolt(ezért választottam). :) Hát gondolni sem mertem volna hogy a képcsövek mind méretbeli,mind geometriai eltérése ellenére a kép szinte tökéletes lett!!!
Nem kell sem vertikálisan sem horizontálisan utána állítani,g2-fókusz szintén jól belőhető.Járattam egy órát,trafó alig langyosodik.
Hát úgy döntöttem beépítem véglegesre ehhez kellene egy kis segítség.
Mivel lehetne a készülék gyári DP142 söntstabilizátorát helyettesíteni hogy ne 142 hanem 125 voltot adjon a tápja? Vagy átalakítani esetleg? A gyári egy kerámialapon kialakított áramkör gőzölt ellenálásokkal és 2db smd alkatrésszel. Van rajta egy 3 lábú smd alkatrész DAL jelöléssel és egy smd dióda+ 2ellenállás.
Valakinek valami ötlete?
Üdv!