Service manuals, schematics, eproms for electrical technicians

PANASONIC TC-21S10R

TV - EPROM
Type: (RAR)
Size
2.6 KB
Page
---
Category
TV
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar panasonic manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Please tick the box below to get download link:
  • Also known:
    PANASONIC TC-21S-10R TC21S10R TC 21 10 21S10R TC-21S10R
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Panasonic TX-L32U2E (GLP25 sasszé) nincs kép sem hang
Űdv Mindenkinek !!!! Kűzdök ezzel a készülékkel,hibajelenség a következő: -stdby ok ,bekapcsoláskor átvált zöldre a led de a szokványostól gyorsabban pislog mig teljesen zöld lessz,, távira reagál bekapcsool, de nem tudom kikapcsolni stdby-ba - invertert nem inditja még egy villanás erejéig sem,tettem antennát és hang sincs.. - ha járatom,kb 10 perc után kattan a relé 1-2er, 2-3 perc mulva piros led 13-as hibakódot jelez. A táp mérve jónak tűnik a feszkók megvannak,én a mainboard-ra tippelek.. az eservice-ről letöltöttem a SM-t csak sajnos nem tudom megnyitni.. minden segitséget eőre is köszönök gyurmonc
PANASONIC - TX-32DK20D
Sziasztok Kérlek segítsetek egy alkatrész beszerzésében. Természetesen leírom a hiba jelenséget is. Adott egy Panasonic tx-32dk20d tv, mely egy sajnálatos kábeltv okozta földhurok miatt tönkrement. (sz.gép-tv összekötve) Pontosabban a tv videó jel bemenetei sorra tönkrementek. audió jel átmegy a kiválasztott beneten. Később megadta magát a sz.gép videokártya tv-outja is. A kapcsolási rajzot bújva ( melyet ezen az oldalon leltem fel, köszönet érte) arra jutottam hogy a videó processzor a ludas. (VPC3215CB8TP - csattolva) Tudnátok nekem ajánlani egy oldalt ahol meg tudom rendelni? Előre is köszönöm!
Panasonic TX-L42ETW5 Device does not start anymore, stand-by LED lights up red, no SOS error code
Manufacturer: Panasonic

Type: TX-L42ETW5

Chassi: LA35



Hello everybody,

I could determine or measure the following with the device:

Device does not start anymore, stand-by LED lights red when device is plugged in and flashes red as soon as an IR command (key press) is sent via the remote control. Voltages of power supply STB 5V and signal LCD_TV_SUB_ON come from A-board. Power supply starts, supplies P15V and SUB1.1V, 1.5V, 1.8V, 3.3V, 5V, HDMI3.3V and USB5V are generated on the A-Board (stand for about 2.5 seconds). Then signal LCD_TV_SUB_ON goes low (voltages go away to STB 5V) and after about 2 seconds back to high (endless). What is missing is the voltage PNL12V which is switched on by PANEL_VCC_ON2. PANEL_VCC_ON2 always has a low signal and does not change its state. Power supply also provides for the 2.5 seconds the 24V for the backlight. Clocking of LCD_TV_SUB_ON starts immediately after plugging in the mains plug (also without IR command). SOS error code is not output. The over-voltage circuit in IC 5000 pin 7 also does not respond. Attached is the timing diagram from the technical training of Panasonic where I have drawn until when the boot process behaves normally.

In my opinion a mistake on the A-board? Does anyone have a tip?

greetings

Andi
Panasonic TH-42PZ8ES nagyon rossz kép--megoldva
Sziasztok!
Olyan a kép, mint amikor CRT-k -nél pl. a zöld katód gyenge és mosódik a szín. AV és tuner bemenetről is ezt csinálja, viszont az OSD hibátlanul jelenik meg.  
Az alaplap: TNPH 0740  1A. Javítható ez, vagy komplett csere?
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce