Service manuals, schematics, eproms for electrical technicians

PANASONIC TC 29S10

TV - EPROM
Type: (E2P)
Size
2.1 KB
Page
---
Category
TV
EPROM
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar panasonic manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Please tick the box below to get download link:
  • Also known:
    PANASONIC TC 29S10 29 10
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Panasonic Plasma TH-85PF12E Error code " 4 Blinks "
 This elderly monster arrived with the error “ 4 blinks “ which the manual suggests is a power board fault

There are TWO power boards and a standby power board inside

On removing rear cover there were two swollen 220uf caps on the standby board, sadly replacing them the 4 blinks remained

Swapping the two power boards over[ as they look identical , gives a “ 2 Blink “ error , the limited info in the manual suggesting that the fault is on the lower board [ main 2 ]

Both boards have a PFC voltage of around 380 volts at switch on before the relays click out

I have done cold checks on both boards and there are no obvious differences

As the manual has only a block diagram of the power supply  it’s difficult to be sure of values / voltages

Has anybody seen or worked one of these or similar beasts and managed to diagnose the problem 

Thanks for looking 

Regards  Ken 
Panasonic TX-L32U2E (GLP25 sasszé) nincs kép sem hang
Űdv Mindenkinek !!!! Kűzdök ezzel a készülékkel,hibajelenség a következő: -stdby ok ,bekapcsoláskor átvált zöldre a led de a szokványostól gyorsabban pislog mig teljesen zöld lessz,, távira reagál bekapcsool, de nem tudom kikapcsolni stdby-ba - invertert nem inditja még egy villanás erejéig sem,tettem antennát és hang sincs.. - ha járatom,kb 10 perc után kattan a relé 1-2er, 2-3 perc mulva piros led 13-as hibakódot jelez. A táp mérve jónak tűnik a feszkók megvannak,én a mainboard-ra tippelek.. az eservice-ről letöltöttem a SM-t csak sajnos nem tudom megnyitni.. minden segitséget eőre is köszönök gyurmonc
Panasonic TX-32pm11d shutting down
Hello, I am working on a panasonic tv that shuts down a few seconds after it comes on, blinks(red standby light remains on)three times pauses, and repeat the cycle. Any ideas as to what could be wrong? Thanks.
Panasonic TX-68PS20A GP3 chassis. No NTSC-M option?
Hello, I have a Panasonic TX-68PS20A 68cm (29") Television with a GP3 chassis. (Australian PAL model) The documentation I have found online says that the gp3 chassis supports VHF PAL-B/G and NTSC-M. However my tv doesnt support M audio. It just tunes the video and gives white noise through the audio since it's looking for B audio even though it's displaying ntsc video just fine. I have found no options for this in any of the service menus I've accessed. Am I missing something? I don't mind if I have to reflash something to make this work. Here is the pdf which I read the specs from, it's not for this model but a similar one with a gp3 chassis. http://elektrotanya.com/cgi-bin/download2.cgi?uid=37145&cid=1417425157&fid=117149&file=panasonic_tx-29psxx_gp-3.pdf&x=26&y=30
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce