Service manuals, schematics, eproms for electrical technicians

PANASONIC TH42PX60 PICTURE DISAPPEARS AFTER FEW MINUTES BUT SOUND IS OK TT-08-14

TV - INFO-TIPS
Type: (PDF)
Size
140.3 KB
Page
1
Category
TV
INFO-TIPS
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar panasonic manual?
Document preview [1st page]
PANASONIC TH42PX60 PICTURE DISAPPEARS AFTER FEW MINUTES BUT SOUND IS OK TT-08-14 service manual (1st page)
Preview of PANASONIC TH42PX60 PICTURE DISAPPEARS AFTER FEW MINUTES BUT SOUND IS OK TT-08-14 [1st page]
Click on the link for free download!
Advertisements
Please tick the box below to get download link:
  • Also known:
    PANASONIC TH-42PX-60 DISAPPEARS AFTER FEW MINUTES BUT SOUND IS OK TT-0814 TH42PX60 PICTURE TT0814 TH 42 PX 60 TT 0814 08 14 TT-08-14
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
PANASONIC TX29PM11P tv chassis GP2
Tisztelt Fórumozók ! Ehhez a készülékhez keresek TNP8EA021 tipusszámú modult. Kérem ha valakinek van ilyen modulja és teremészetesen eladó jelezze azt. Köszönettel:kerekguriga
Panasonic tx40c320e tv nem indul, led villog
Sziasztok.

Panasonic tx40c320e
17mb97
ves400unss-2d-u01
 
A jelenség hogy nem indul csak a led pislog. Remélem szoft probléma. Esetleg ha lenne valakinek szoftja usb re es elküldené  megköszönném.
Panasonic LED TV, vélemények
Sziasztok!

Előbb-utóbb le kell cserélni a jó öreg 4:3 Sony Trinitron képcsöves tévénket. Egy külföldi fórumon talált amerikai öreg szaki tévészerelő véleménye szerint minden márka minden készüléke "crap", egyet kivéve: a Panasonic Viera LED tévéket. Azok állítólag rendesen meg vannak csinálva. A többi, LG, Samsung, Sony, stb. szerinte mind "crap".

Nektek mi erről a tapasztalatotok? Továbbá igaz az, hogy minálunk a Panasonic tévék belseje Vestel, ami ha jól tudom, török. Ha így van, akkor talán mégsem olyan jó (mint az USA-ban forgalmazott Panasonic).

Ha nem Panasonic, akkor mi egyebet ajánlotok, a megbízhatóságra helyezve a hangsúlyt? Okostévé funkciók nem érdekelnek, legyen rajta HDMI és kész. 4K és más csili-vili sem hoz lázba.

Előre is köszönöm.

- lcsaszar
Panasonic TX-L42ETW5 Device does not start anymore, stand-by LED lights up red, no SOS error code
Manufacturer: Panasonic

Type: TX-L42ETW5

Chassi: LA35



Hello everybody,

I could determine or measure the following with the device:

Device does not start anymore, stand-by LED lights red when device is plugged in and flashes red as soon as an IR command (key press) is sent via the remote control. Voltages of power supply STB 5V and signal LCD_TV_SUB_ON come from A-board. Power supply starts, supplies P15V and SUB1.1V, 1.5V, 1.8V, 3.3V, 5V, HDMI3.3V and USB5V are generated on the A-Board (stand for about 2.5 seconds). Then signal LCD_TV_SUB_ON goes low (voltages go away to STB 5V) and after about 2 seconds back to high (endless). What is missing is the voltage PNL12V which is switched on by PANEL_VCC_ON2. PANEL_VCC_ON2 always has a low signal and does not change its state. Power supply also provides for the 2.5 seconds the 24V for the backlight. Clocking of LCD_TV_SUB_ON starts immediately after plugging in the mains plug (also without IR command). SOS error code is not output. The over-voltage circuit in IC 5000 pin 7 also does not respond. Attached is the timing diagram from the technical training of Panasonic where I have drawn until when the boot process behaves normally.

In my opinion a mistake on the A-board? Does anyone have a tip?

greetings

Andi
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce