Service manuals, schematics, eproms for electrical technicians

PANASONIC TX-2170T,TC-2170R CH MX-3 SM.

TV - SERVICE MANUAL
Type: (DJVU)
Size
1.5 MB
Page
34
Category
TV
SERVICE MANUAL
If you get stuck in repairing a defective appliance download this repair information for help. See below.
Good luck to the repair!

Please do not offer the downloaded file for sell only use it for personal usage!

Looking for similar panasonic manual?
Document preview [1st page]
No preview item


No preview item for this file.

Possible causes:
  • No preview picture generated yet.
  • It is not a pdf file.
Advertisements
Download free of charge (10 files / day):
Download is being processed. Please wait...
Download processing...
  • Also known:
    PANASONIC TX-2170T TC-2170R CH MX-3 TX2170T TC2170R MX3 SM. TX 2170 TC MX 2170T 2170R
  • If you have any question about repairing write your question to the Message board. For this no need registration.
  • If the site has helped you and you also want to help others, please Upload a manual, circuit diagram or eeprom that is not yet available on the site.
    Have a nice Day!
  • See related repair forum topics below. May be help you to repair.
Warning!
If you are not familiar with electronics, do not attempt to repair!
You could suffer a fatal electrical shock! Instead, contact your nearest service center!

Note! To open downloaded files you need acrobat reader or similar pdf reader program. In addition, some files are archived,
so you need WinZip or WinRar to open that files. Also some files are djvu so you need djvu viewer to open them.
These free programs can be found on this page: needed progs
If you use opera you have to disable opera turbo function to download file!
If you cannot download this file, try it with CHROME or FIREFOX browser.
Translate this page:
Relevant TV forum topics:
Panasonic TX+P42ST60E 8 villogás
Üdv Mesterek!

Adott a tárgybéli plazma TV. Némi baszogatás ki-be kapcsolgatási próbálkozás után bekapcsol a TV, de nem sokáig működik max fél percig, utána kikapcsol és 8-at villog a készenléti ledje. Még nem láttam a készüléket, de mi lehet ezzel, mi okozhat ilyen hibát? Köszönöm előre is az építő jellegű tippeket 
RGB Mod in Panasonic CTP-2780SF

Anyone ever do one of these to a CRT?

Seems like the set has this jungle IC which will be where the RGB lines
for the OSD are needed for the mod:

https://pdf1.alldatasheet.com/datasheet-pdf/view/13342/PANASONIC/AN5304NK.html

Am not sure what the line would be that tells the chip to turn the OSD on. Apparently there
is a line if its 1 volt or more, it activates the OSD, if zero its normal video.

Also I think there must be a sync line tapped into which is bought out to the rear of the set,
with the (3) RGB lines / jacks but not sure where that would be tapped into?

I am gonna use BNC jacks, not the scart connector.
There are some youtube videos about RGB modding and lots of topics on the shumps
forums but so far it seems no one has tried this with Panasonic.

 

Steve Hearns
Technotronic Dimensions, VT [USA]
WWW.TECHNOTRONIC-DIMENSIONS.COM

Panasonic TH-42PX80E plazma TV nem indul (valtozott, indul, de beteg)
Sziasztok
Van nalam egy ilyen TV:
Panasonic TH-42PX80E plazma TV
A PFC reszben levo Q406 FET tranzisztor zarlatos volt, a tipusa RJK5010
Ki volt egve  a halozati reszen F401 es F402 biztositek, a tipusa T8AH
Az D401 egyeniranyito hidban zarlatos volt 2 dioda. A hid tipusa a rajta levo jeloles szerint D6SB 80 a rajz szerint B0FBAT000006 (800V/6A)

Ezeket csereltem es meg meregettem a TV-ben de nem talaltam mas hibat.
Csere utan ugy tunt, hogy valami csattant uzembe helyezeskor. Aramtalanitottam es meregettem benne, de minden jo volt.
Utana ismet bedugtam es megfigyeltem a LED-eket.
Amikor aramot kap, a piros LED 10-et pislog. Ez a F_STB +15V vagy valamelyik belole eredo feszultseg hianyat jelenti.
Ha megnyomoma bekapcsolo gombot, pislog a zold LED, de utana ismet 10 piros pislogas.
A kovetkezokre jottem ra:
A STB5V megvan, betapolja a maint, az megadja 15 masodpercig a F_STB_ON feszultseget (3.2V), de F_STB (+15V) nincs.
Tovabb meregetve rajottem, hogy a R448 es R449 teljesitmeny ellenallasok ( 0.12 Ohm/5W) ami a tapot csatolja, szakadtak.
Most jon a kerdesem:
Szerintetek ezek is ki voltak egve amikor elszallt a Graetz, a biztositekok es a FET, vagy pedig van valami zarlat amit nem talaltam meg, es most szallt el? Merve a cserelt alkatreszek most jok.
Elore is koszonok minden velemenyt, minden jot,

Janos
Panasonic TH-42PV80PA
Fent nevezett gép kikapcsol ahogy bekapcsolnám és a készenléti led 7-t villog. Elvileg tápok rendben lennének. Valakinek ötlete? Köszi Jah Y board cserélve volt de nem az a baja ahogy az eurasban is írták - volna -. Köszi
Similar manuals:
If you want to join us and get repairing help please sign in or sign up by completing a simple electrical test
or write your question to the Message board without registration.
You can write in English language into the forum (not only in Hungarian)!

E-Waste Reduce